POSIFLEX LM-7115 User Manual
POSIFLEX LM-7115 User Manual

POSIFLEX LM-7115 User Manual

Lcd touch monitor
Hide thumbs Also See for LM-7115:

Advertisement

LM-/TM-7115/7115N
LCD Touch Monitor
User's Manual
I.
FEATURES
• Most stable 15" LCD monitor with tilt adjust for
industrial and commercial use.
• Application covers POS, Factory Automation etc.
• High quality 15" TFT LCD panel with scaling function for full screen
display
• Easy maintenance structure allowing easy cleaning
• Tilt adjustable yet robust and wobble free construction
• Recommended LCD resolution: 1024 x 768
• Resistive type extra long life touch panel in USB interface supports touch
panel function including left/right button, double click, drag & drop(For
TM-7115/7115N)
• Touch beep can be pitch adjusted/enabled/disabled by software control(For
TM-7115/7115N)
• Connect to host through VGA port plus USB port (for all models) and/or
COM port (for TM-7115/7115N's RS232 touch model only)
• Support 2 downlink USB ports
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the Touch Monitor TM-7115 & TM-7115N. This product provides exquisite touch control
capability over a stable and adjustable LCD monitor with minimal footprint.
The manufacturer of the LM-/TM-7115/7115N touch monitor heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology. The user
may always obtain the most up to date information through any of our web sites: http://www.posiflex.com,
http://www.posiflex.com.tw, http://www.posiflexusa.com.
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
19690900030
P/N:
Rev. B0
© Copyright Posiflex Technology, Inc. 2010
Part 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LM-7115 and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX LM-7115

  • Page 1 LM-/TM-7115/7115N LCD Touch Monitor User’s Manual Rev. B0 FEATURES • Most stable 15” LCD monitor with tilt adjust for industrial and commercial use. • Application covers POS, Factory Automation etc. • High quality 15” TFT LCD panel with scaling function for full screen display •...
  • Page 2: Carton Contents

    II. CARTON CONTENTS 1. Touch Monitor (Main unit + Adjustable base stand assembly) 2. User’s Manual 3. VGA cable 4. USB cable 5. Power adaptor: 12 V DC & power cord 6. Posiflex Product Information CDROM 7. Option RS232 cable 8.
  • Page 3: Input/Output Ports

    IV. INPUT / OUTPUT PORTS 12 V DC RJ45 Jack USB (B) USB (A) option (option RS232 for input input (to Host) (to Devices) Audio input TM-7115) V. AVAILABLE OPTION ITEMS 1. Audio port for multimedia application 2. Side mount upgrade kit FA-200 with MSR / Fingerprint sensor 3.
  • Page 4 Cable Connections In order to settle the touch monitor properly in a point of sale system, all the cable connections have to be routed through its base. Therefore, please observe the procedures from A to C below to separate the main unit from the base stand assembly after all cables in connection area disconnected.
  • Page 5 Option Wall Mount Kit Select a flat surface on wall of adequate strength and with proper ventilation and space condition. Please use the right material to hold this monitor according to the wall material (Drywall, concrete, solid wood, etc). Consult with your contractor if it is necessary.
  • Page 6 Edge Accel. – This function engages the “Posiflex USB Touch Edge Acceleration Tool” and helps to find the hidden taskbar or thin scroll bar through touch. Enable Touch – This check box must be checked to have the touch panel working. Enable Touch_to_Calibrate –...
  • Page 7 Compensation – This list button selects the distance to advance the mouse toward edge from touch point. USB touch right button tool This tool differs slightly from the “Touch as Right Button Click” check box in the USB touch manager. When executed, there will be a small window of “One Shot Right Button”...
  • Page 8 IX. OSD (ON SCREEN DISPLAY) SCREEN ADJUST FUNCTION OSD buttons The 4 OSD control buttons are above the power switch button on left side of the LCD panel. “OSD” button: To enter OSD setup menu, or to perform function selected in OSD operation. “NXT”...
  • Page 9 button to increase contrast. Press “-” to decrease. Press “OSD” button to save the current setting and return to “Brightness/Contrast submenu”. “EXIT”: Return to “Main menu”. “COLOR ADJUST SUBMENU”: There are 4 icons in this submenu: Press “OSD” button to select item or return to main menu. Press “NXT”...
  • Page 10 “7500K”: Pressing “OSD” button on this icon will set the color balance to a color temperature of 7500 degrees Kelvin. “9300K”: Pressing “OSD” button on this icon will set the color balance to a color temperature of 9300 degrees Kelvin. “EXIT”: Return to “Color adjust submenu”.
  • Page 11 adjust submenu”. “EXIT”: Return to “Main menu”. “TOOLS SUBMENU”: When this item is selected, there are 5 icons in this submenu: Press “OSD” button to select item or return to main menu. Press “NXT” button to select among OSD submenu, reset to default, phase, smoothness / sharpness adjust, mode select and exit.
  • Page 12: Supported Display Modes

    frequency of 37.9KHz and pixel frequency of 31.5MHz making it impossible for automatic select. These modes are not used in normal Windows display. “EXIT”: Return to “Main menu”. “EXIT”: Exit OSD setup with all adjustment saved. X. SUPPORTED DISPLAY MODES For video signals beyond the supported display modes, there will be a message “Out Of Range”...

This manual is also suitable for:

Tm-7115Lm-7115nTm-7115n

Table of Contents