Table of Contents
Advertisement
Quick Links
LM/TM-7115/7115N/7115IR
LCD Touch Monitor
User's Manual
I.
FEATURES
• Most stable 15" LCD monitor with tilt adjust for
industrial and commercial use.
• Application covers POS, Factory Automation etc.
• High quality 15" TFT LCD panel with scaling function for full screen
display
• Easy maintenance structure allowing easy cleaning
• Tilt adjustable yet robust and wobble free construction
• Recommended LCD resolution: 1024 x 768
• Durable resistive type touch panel for TM-7115/7115N that endures 35
million touches min. at same spot or Infra-Red touch panel for TM-7115IR
• Supports touch panel function including left/right button, double click, drag
& drop (for TM only)
• Touch beep can be pitch adjusted/enabled/disabled by software control
(for TM only)
• Support 2 downlink USB ports
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the Touch Monitor TM-7115 & TM-7115N & TM-7115IR. This product provides exquisite
touch control capability over a stable and adjustable LCD monitor with minimal footprint.
The manufacturer of the LM/TM-7115/7115N/7115IR LCD/touch monitor heartily apologizes to the user for reserving the right to
change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com,
http://www.posiflex.com.tw, http://www.posiflexusa.com.
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
19690900050
P/N:
Rev. D0
© Copyright Posiflex Technology, Inc. 2011
Part 1
Advertisement
Table of Contents
Related Manuals for POSIFLEX LM-7115IR
Summary of Contents for POSIFLEX LM-7115IR
- Page 1 The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com, http://www.posiflex.com.tw, http://www.posiflexusa.com.
-
Page 2: Carton Contents
2. User’s Manual 3. VGA cable 4. USB cable 5. Power adaptor: 12 V DC & power cord 6. Posiflex Product Information CDROM 7. Option RS232 cable 8. Option Audio cable III. INSTALLATION GUIDE OF MONITOR Since the monitor and stand are packaged... -
Page 3: Parts Identification
IV. PARTS IDENTIFICATION FRONT VIEW Main Unit Display Screen + Touch Panel Logo + Power Indicator Adjustable Base Option Assembly FA-200 SIDE VIEWS Lock/release button to detach the main unit Control button area Push in this direction to adjust the tilt angle Lock/release lever of the display panel OSD button... -
Page 4: Hardware Installation
VI. AVAILABLE OPTION ITEMS 1. Audio port for multimedia application 2. Side mount upgrade kit FA-200 with MSR / Fingerprint sensor 3. Wall mount kit (WB-6000V-B) 4. RS232 interface Infra-Red type touch panel (TM-7115IR) VII. HARDWARE INSTALLATION Option Multi-Media Function When this option is ordered with the LM/TM-7115/7115N/7115IR touch monitor, the 3.5 mm diameter stereo jack and 2 internal 2W speakers with amplifiers are already installed. - Page 5 Step A: Prepare a soft clean flat surface, such as a piece of cloth on the desk to seat the front surface of main unit Step B: Press the Lock/Release button for main unit detach and meantime ... Step C: Slide the base stand assembly to the right to separate the main unit from base stand Refer to the bottom view picture of the...
-
Page 6: Driver Installation
The USB interface touch controller operates as an USB mouse without need for any special driver in Windows. However, there is a program supported for its calibration and touch function manipulation. Please find it in the attached Posiflex product information... - Page 7 Please go to “Program Files” and select “Posiflex USB Touch Tools” and then select “Posiflex USB Touch Manager” within the tools to engage this utility. Most items in this utility should be easily understandable to average user.
- Page 8 If the TM-7115/7115N system purchased is the RS232 interface Resistive type touch panel or the TM-7115IR leading edge Infra Red type touch models, the touch controller is of RS232 interface. The “Posiflex Touch Terminal Manager” above should be disregarded. In case there is any external COM port summoned for this purpose, that COM position of the system will be covered in the connection area.
- Page 9 and “Elo Touchscreen” or just click the “elo” icon in tool tray to engage this utility. However, with this touch controller driver, certain display mode like full screen display of Windows DOS box should be avoided. APPLICATION LIMITATION The USB touch is not applicable for OS other than Windows as USB mouse is not supported in DOS environment and there is difficulty in engaging driver to convert the coordination system between the static panel and the dynamic mouse in Linux environment.
- Page 10 (On Screen Display adjustment). The OSD window will pop up on the screen. On top part of this window is a Posiflex logo with the OSD firmware version indicated to its lower right. Below this area is a row of icons for main OSD menu.
- Page 11 button to increase contrast. Press “-” to decrease. Press “OSD” button to save the current setting and return to “Brightness/Contrast submenu”. “EXIT”: Return to “Main menu”. “COLOR ADJUST SUBMENU”: There are 4 icons in this submenu: Press “OSD” button to select item or return to main menu. Press “NXT”...
- Page 12 “7500K”: Pressing “OSD” button on this icon will set the color balance to a color temperature of 7500 degrees Kelvin. “9300K”: Pressing “OSD” button on this icon will set the color balance to a color temperature of 9300 degrees Kelvin. “EXIT”: Return to “Color adjust submenu”.
- Page 13 adjust submenu”. “EXIT”: Return to “Main menu”. “TOOLS SUBMENU”: When this item is selected, there are 5 icons in this submenu: Press “OSD” button to select item or return to main menu. Press “NXT” button to select among OSD submenu, reset to default, phase, smoothness / sharpness adjust, mode select and exit.
-
Page 14: Supported Display Modes
frequency of 37.9KHz and pixel frequency of 31.5MHz making it impossible for automatic select. These modes are not used in normal Windows display. “EXIT”: Return to “Main menu”. “EXIT”: Exit OSD setup with all adjustment saved. XI. SUPPORTED DISPLAY MODES For video signals beyond the supported display modes, there will be a message “Out Of Range”...
Need help?
Do you have a question about the LM-7115IR and is the answer not in the manual?
Questions and answers