Troy-Bilt TB465SS Operator's Manual

Troy-Bilt TB465SS Operator's Manual

4-cycle gasoline trimmer
Hide thumbs Also See for TB465SS:

Advertisement

®
Operator's Manual
TABLE OF CONTENTS
Service Information
....................................
1
Rules for Safe Operation
................................
2
Oil and Fuel Information
................................
3
Assembly Instructions
..................................
4
Know Your Unit .......................................
4
Starting/Stopping
Instructions
............................
5
Operating Instructions
..................................
6
Maintenance
and Repair Instructions
......................
7
Cleaning and Storage
.................................
10
Troubleshooting
Chart .................................
11
Specifications
.......................................
12
Warranty Information
..................................
13
Parts List
..............................
Inside Back Cover
WARNING:
When using the unit, you must follow the
safety rules. Please read these instructions
before
operating the unit in order to ensure the safety of the
operator and any bystanders. Please keep these
instructions
for later use.
4-Cycle Gasoline Trimmer
Model TB415CS
&
Model TB465SS
SAVE THESE INSTRUCTIONS
For service call 1-800-520-5520
to obtain a list of authorized service
dealers near you. For more details about your unit, visit our website at
www.troybilt.com.
DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF
PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.
THIS PRODUCT
IS COVERED
BY ONE OR MORE U.S. PATENTS.
OTHER PATENTS PENDING.
Service on this unit both within and after the warranty period should be
performed only by an authorized and approved
service dealer.
SPARK ARRESTOR
NOTE
NOTE:
For users
on U.S.
Forest
Land and
in the states
o1
California,
Maine, Oregon and Washington.
All U.S. Forest Land and
the state of California
(Public
Resources
Codes
4442 and 4443),
Oregon
and Washington
require,
by law that
certain
internal
combustion
engines operated
on forest
brush and/or
grass-covered
areas
be equipped
with a spark
arrestor,
maintained
in effective
working order, or the engine be constructed,
equipped
and maintained
for the prevention of fire. Check with your state or local authorities
for
regulations
pertaining
to these requirements.
Failure to follow these
requirements
could subject you to liability or a fine. This unit is factory
equipped
with a spark arrestor.
If it requires replacement,
ask your
LOCAL SERVICE DEALER to install the Accessory
Part #180890
Spark Arrestor
Kit.
CALIFORNIA
PROPOSITION
65 WARNING
THE ENGINE EXHAUST FROM THIS PRODUCT
CONTAINS
CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO
CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVEHARM.
All information,
illustrations,
and specifications
in this manual are based
on the latest product
information
available at the time of printing. We
reserve the right to make changes at any time without notice.
Copyright©
2004 MTD SOUTHWEST
INC, All Rights Reserved.
P/N 769-01955
(10/05)
PRINTED IN USA

Advertisement

Table of Contents
loading

Summary of Contents for Troy-Bilt TB465SS

  • Page 1 ® Operator's Manual 4-Cycle Gasoline Trimmer Model TB415CS & Model TB465SS SAVE THESE INSTRUCTIONS For service call 1-800-520-5520 to obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.troybilt.com. DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.
  • Page 2: Before Operating

    • IMPORTANT SAFETY INSTRUCTIONS • trimming lines extended, and the proper line installed. Do not extend READ ALL INSTRUCTIONS the trimming line beyond the length of the shield. BEFORE OPERATING • This unit does not have a clutch. The cutting attachment continues •...
  • Page 3 This o perator's manual describes safety and international symbols and pictographs that m ay appear onthis product• Read t he operator's manual forcomplete safety, assembly, operating and maintenance and repair information• SYMBOL MEANING SYMBOL MEANING ' SAFETY ALERT SYMBOL ON / START / RUN Indicates danger, warning or cautionl May be used * ON/OFF STOP CONTROL in conjunction...
  • Page 4: Fueling The Unit

    ADJUSTING THE D-HANDLE NOTE: The D-handle comes mounted on the backside of the shaft. Locate the wing nut on the D-Handle. Untighten the wing nut enough to loosen the D-Handle (Fig. 5). NOTE: Do not remove wing nut, washer, or bolt. Rotate the D-Handle to the upright position on the front side F ill...
  • Page 5: Starting Instructions

    Stop/Off WARNING: Operate this unit only in a well-ventilated Start/On outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig.
  • Page 6: Holding The Trimmer

    WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. WARNING: Never use metal-reinforced line, wire, chain, or rope. These can break off and become HOLDING THE TRIMMER dangerous projectiles. Before operating the unit, stand in the operating position (Fig.
  • Page 7: Maintenance Schedule

    MAINTENANCE SCHEDULE From inside the cutting attachment shield, push the square bolt through the hole until the threaded end protrudes through the guard Perform these required maintenance procedures at the frequency mounting bracket (Fig. 18). stated in the table. These procedures should also be a part of any seasonal tune-up.
  • Page 8: Air Filter Maintenance

    1. Unplug spark plug b oot to prevent accidental starting. 2. Remove the oil f ill plug/dipstick. 3. Pour the oilout o fthe oil f ill hole a nd into acontainer tipping the unit t oavertical position (Fig. 21). Allow ample time forcomplete drainage.
  • Page 9: Carburetor Adjustment

    WARNING: The cutting attachment may spin during idle speed adjustments. Wear protective clothing and observe all safety instructions to prevent serious personal injury. CARBURETOR ADJUSTMENT The idle speed of the engine is Idle Adjustment Screw adjustable. An idle adjustment screw is reached though a hole in the top of the engine cover (Fig.
  • Page 10: Maintenance

    RockerArms If using a torque wrench torque to: 110-120 in.olb. (12.3-13.5 N*m) Adjusting Nuts INTAKE Do not over tighten. SPARK ARRESTOR MAINTENANCE Remove the muffler cover. See RockerArm Clearance. EXHAUST With a flat blade screwdriver or Torx T-20 bit, remove the screw attaching the spark arrestor cover to the muffler (Fig.
  • Page 11 CAUSE ACTION Fill fuel tank with new fuel Empty fuel tank Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times Old fuel Drain gas tank and add fresh fuel Fouled spark plug Replace or clean the spark plug Plugged spark arrestor Clean or replace spark arrestor When it is above 40°F outside &...
  • Page 12 ........................3 inches (76.2 mm) Trimming Line Diameter: TB415CS & TB465SS ................0.105 inches (2.667 mm) square cutting line TB415CS & TB465SS Cutting Path Diameter ............................16 inches (40.64 cm) *All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time...
  • Page 13: Owner's Warranty Responsibilities

    • As the small off-road engine owner, you however should be aware that Troy-Bilt may deny you warranty coverage if your small off-road engine or a par_ has failed due to abuse, neglect, improper maintenance or unapproved modifications.
  • Page 14: Limited Warranty

    No other express warranty or guaranty, whether The limited warranty set forth below is given by Troy-Bilt LLC with respect written or oral, except as mentioned above, given by any person or to new merchandise purchased and used in the United...
  • Page 15 ENGINE PARTS - MODELS TB415CS & TB465SS 4-CYCLE GAS TRIMMERS...
  • Page 16 ENGINE PARTS - MODELS TB415CS & TB465SS 4-CYCLE GAS TRIMMERS Item Part No. Item Part No. Description Description 753-04288 Palnut 753-04083 Engine Cover 753-1202 Plate Screw 791-181930 Engine Cover Screws 791-181025 Valve Cover Screw 753-05074 Pressure Plate Assembly (includes 43)
  • Page 17 BOOM AND TRIMMER PARTS - MODEL TB415CS 4-CYCLE GAS TRIMMER Item Part No. Description 753-04234 Throttle Housing Assembly (includes 2-4) 791-182405 Switch 753-04119 Throttle Trigger 791-182690 Throttle Trigger Spring 753-05162 Drive Shaft Housing Assembly 791-153064 D-Handle (includes 7) 791-181587 Handle Hardware 753-04282 Guard Mounting Hardware 753-04283...
  • Page 18 BOOM AND TRIMMER PARTS - MODEL TB465SS 4-CYCLE GAS TRIMMER Item Part No. Description 753-04234 Throttle Housing Assembly (includes 2-4) 791-182405 Switch 753-04119 Throttle Trigger 791-182690 Throttle Trigger Spring 753-05166 Drive Shaft Housing Assembly (includes 8) 791-153064 D-Handle (includes 7)

This manual is also suitable for:

Tb415cs

Table of Contents