Table of Contents
Advertisement
Advanced Features
If you wish to make adjustments to other items
on the
menu, press the
SYSTEM SETUP
Navigation Button
to place the
⁄
/
¤
blue cursor bar on the desired item and press
the Set Button
to make an adjustment to
another menu. If you have completed all adjust-
ments, press the OSD Button
menu system.
Turn On Volume Level
As is the case with most audio/video receivers,
when the AVR is turned on, it will always return
to the volume setting in effect when the unit
was turned off. However, you may prefer to
always have the AVR turn on at a specific set-
ting, regardless of what was last in use when
the unit was turned off. To change the default
condition so that the same volume level is
always used at turn-on, you will need to make
an adjustment in the
SYSTEM SETUP
menu. To start the adjustment, press the OSD
button
to bring the main menu (Figure 1) to
the screen. Press the
button
⁄
System
-tab is highlighted in white. Press the
Set button
to enter the
SYSTEM
SETUP
menu (Figure 32).
At the
SYSTEM SETUP
menu make certain
that the blue cursor bar is on the
Volume
Default
line by pressing the
⁄
as needed. Next, press the Set Button
, followed by the
‹
›
buttons
/
that the word
is shown in the video display
O N
and press Set
to confirm. Next, press the
button
once so that the blue cursor bar
¤
highlights the
Default Volume Set
line. To set the desired turn-on volume, press the
Set Button
, followed by the
‹
or hold them pressed until the desired
volume level is shown on the
Default
Volume Set
line and press the Set Button
to confirm. Note that this setting may NOT
be made with the regular volume controls.
NOTE: Since the setting for the turn-on volume
cannot be heard while the setting is being made,
you may wish to determine the setting before
making the adjustment. To do this, listen to any
source and adjust the volume to the desired
level using the regular volume controls
When the desired volume level to be used at
turn-on is reached, make a note of the setting as
it appears in the lower third of the video screen
or in the Main Information Display Ò.
A typical volume level will appear as a negative
number such as -25dB. When making the
adjustment, use the
‹
›
buttons
/
enter this setting.
50 ADVANCED FEATURES
Unlike some of the other adjustments in this
menu, the turn-on volume default will remain in
effect even when the unit is turned off
completely, unless it is changed or turned off in
this menu.
If you wish to make other adjustments in the
to exit the
menu, press the
screen blue cursor bar is highlighting the desired
setting. If you have no other adjustments to
make, press the OSD Button
menu system.
Semi-OSD Settings
The semi-OSD system places two-line messages
at the lower third of the video display screen
whenever the Volume, Input Source, Surround
mode or tuner frequency of any of the configura-
tion settings are changed. The semi-OSD system
is helpful in that enables you to have feedback
on any control changes or remote commands
using the video display when it is difficult to
view the front-panel displays. However, you may
, until the
occasionally prefer to turn these displays off for
a particular listening session. You may also want
to adjust the length of time the displays remain
on the screen. Both of those options are possible
with the AVR.
To turn off the semi-OSD system, you will need
buttons
/
¤
to make an adjustment in the
menu (Figure 32). To start the adjust-
SETUP
so
ment, press the OSD button
main menu to the screen. Press the
, until the
System
white. Press the Set Button
SYSTEM SETUP
›
buttons
/
At the
SYSTEM SETUP
that the blue cursor bar is highlighting the
Semi OSD Timeout
buttons
/
⁄
¤
Set Button
so that the word
display and press Set
setting.
Note that this setting is temporary and will
remain active only until it is changed or until the
AVR is turned off. Once the unit is turned off, the
semi-OSD displays will remain activated, even if
.
they were switched off for the previous listening
session.
to
Buttons
until the on-
/
⁄
¤
to exit the
SYSTEM
to bring the
Button
⁄
-tab is highlighted in
to enter the
menu.
menu make certain
line by pressing the
as needed. Next, press the
, followed by the
button
›
OFF
is shown in the video
to confirm the new
To change the length of time that the semi-OSD
displays remain on the screen, go to the
OSD Timeout
-line as outlined earlier, and
press the Set Button
. Next, press the
‹
›
Buttons
until the desired time in
/
seconds is displayed and press the Set Button
to confirm the new setting. Note that unlike
most of the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments in the
menu, press the
Buttons
/
⁄
¤
cursor bar is highlighting the desired setting. If
you have no other adjustments to make, press
the OSD Button
to exit the menu system.
Full-OSD Time Out Adjustment
The
menu system is used to
FULL OSD
simplify the setup and adjustment of the AVR
using a series of on-screen menus. The factory
default setting for these menus leaves them on
the screen for 20 seconds after a period of inac-
tivity before they disappear from the screen or
Time Out. This Time Out is a safety measure to
prevent the menu text from burning into the
CRTs in your monitor or projector, which might
happen if they were left on indefinitely. However,
some viewers may prefer a slightly longer or
shorter period before the Time Out display.
To change the Full-OSD Time Out, you will need
to make an adjustment in the
SYSTEM
SETUP
menu (Figure 32). To start the adjust-
ment, press the OSD button
to bring the
main menu to the screen. Press the
, until the
System
- tab on the left is
highlighted in white. Press the Set Button
to enter the
SYSTEM SETUP
At the
SYSTEM SETUP
menu make certain
that the blue cursor bar is highlighting the
line by pressing the
Full OSD Timeout
Buttons
as needed. Next, press the
/
⁄
¤
Set Button
, followed by the
‹
until the desired time is displayed in
seconds and press the Set Button
firm the new setting. Note that unlike most of
the other options in this menu, this is a perma-
nent setting change, and the time-out entry will
remain in effect until it is changed, even when
the unit is turned off.
If you wish to make other adjustments in the
menu, press the
Buttons
/
⁄
¤
blue cursor bar is highlighting the desired set-
ting. If you have no other adjustments to make,
press the OSD Button
to exit the menu sys-
tem.
Semi
until the blue
button
⁄
menu.
›
buttons
/
to con-
until the
Hide quick links:
Advertisement
Table of Contents
