Poulan Pro PP325 Instruction Manual page 12

fences, metal, etc., or clusters of hard,
woody brush having a diameter greater
than 1/2 inch (1 cm).
• Keep the blade sharp. A dull blade is more
likely to snag and thrust.
• Cut only at fuil throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
• "Feed" the blade deliberately and not too
rapidly. The blade can thrust away if it is fed
too rapidly.
• Cut only from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator.
• Use the shoulder strap and keep a firm grip
on the unit with both hands. A properly
adjusted shoulder strap will support the
weight of the unit, freeing your arms and
hands to control and guide the cutting motion.
• Keep feet comfortably spread apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
• Keep blade below waist level; it will be
easier to maintain control of unit.
• Do not raise the engine above your waist as
the blade can come dangerously close to
your body.
• Do not swing unit with such force that you
are in danger of losing your balance.
Bring the engine to cutting speed before enter-
ing the material to be cut.if the blade does not
turn when you squeeze the throttle trigger, make
sure shaft is fully inserted into the engine.
Always release the throttle trigger and allow
engine to return to idle speed when not cut-
ting. The blade should not turn while the en-
gine is running at idle. If the blade turns at idle,
do not use your unit. Refer to the CARBURE-
TOR ADJUSTMENT section or contact your
authorized service dealer.
• Maintain good firm footing while using the
unit. Do this by planting feet firmly in a
comfortable apart position.
• Cut while swinging the upper part of your
body from left to right.
• As you move forward to the next area to cut,
be sure to maintain your balance and footing.
RECOMMENDED CUTTING POSITION
Cut using the 2 _r'l_ .(,_..._...}2
o'clock
o'clock to 4 o'clock
V'r'f'V,'
position of the ./ I I _'&4 o'clock
blade
"IF"
£A ...__.,..._
• _IIWAHNIN_: The operator or others
must not try to clear away cut material with the
engine running or the blade turning to avoid
serious injury. Stop engine and blade before
removing materials wrapped around blade or
shaft.
,tA
='=WARNING:
For each optional at-
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
_WARNING:
Ensure handlebar re-
mains installed on upper shaft (engine end of
unit) at all times.
EDGER SAFETY
WARNING:
Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
• Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
• Allow blade to stop before removing it from
the cut.
Blade rotates Allow blade to stop
before removing it I
after the from the cut. J
tri_lger is _/
released,
• Throw away blades that are bent, warped,
cracked, broken or damaged h_ any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
• Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving.
• Always keep the wheel and depth adjusting
skid in contact with the ground.
• Always push the unit stowIy over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
• Always use the handlebar when using
edger attachment.
BLOWER/VACUUM SAFETY
'_,WARNING:
inspect area before
starting unit. Removeall debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
• Do not set unit on any surface except a clean,
hard area while engine is running. Debris
such as gravel, sand, dust, grass, etc., could
12