Makita JR3030T Instruction Manual page 11
Recipro saw, variable speed
Hide thumbs
Also See for JR3030T:
- Instruction manual (41 pages) ,
- Instruction manual (15 pages) ,
- Instruction manual (33 pages)
Advertisement
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for use with your Makita tool specified in this
manual The use of any other accessories or attachmentsmight present a riskof injuryto persons.
These accessories or attachments
should be used only in the proper and intended manner,
NOTE: The accessories listed in this manual are available at the extra cost from your Makita distri-
butor or Makita Factory Service Center. Service Centers are listed on the warranty card packed with
your tool.
Qty
Teeth
O,*wa0
Tooth
Saw Blad_
Pwt
#
I_r Pkg
Per inch
Length
Specifi.ttom
Wood
Cutting
Bladls
723018-A_5
5
6
6"
High Carbon
Steel
Ream
Ground
723018-A-2
2
S
6"
(0.049")
High Carbon
Steel
723018-B-5
5
6
12"
Fleam
Ground
723018-B-1
1
6
12"
{0.049")
72301S-C-5
5
6
6"
Milled
(0.031
")
•
High Alloy
Steel
723018-D-5
5
10
6"
High Alloy
Steel
723018-D-2
2
10
6"
Milled
(0.031
")
723018-E-5
723018-P-5
H_h
Carbon
Steel
6"
Ream
Ground
(0.049")
High Atloy
Steet
6"
M/V
Alternate
[0.041
"')
High Speed Steel
Metal
Cutting
Blades
723019_-5
5
14
4""
Mitled/Raker
Set
723019-G-2
2
14
4"
(0.031'*)
For rapid cutting
of
metal
Bnd fiberglass,
High Speed Steel
Made of high speed
723019-A-5
S
14
6"
Milled/Raker
Se_
steel.
723019-A-2
2
14
6"
(0.031
"(
723019-B-5
5
18
4"
High Speed Steel
Milisd/Raker
Set
,
•
723019-B-2
2
18
4"
(0.031
'*)
High S_ed Steel
_J_
%
723019-H-5
a
18
4"
Milled/Wavy Set
(0.049")
High Speed Steel
723019_-5
5
18
6"
Milled/Re
ker Set
723019_-2
2
18
6"
(0.031")
723019-K-5
a
24
4-
High SOeed Steel
723019-K-2
2
24
4"
Milled/Waw
Set
(0.031
")
24
24
36
723019-D-5
723019-D-2
723019J-5
6"
High SPeed Steel
6"
Milled/Wavy
Set
(0,031
")
High Soeed Steel
4"
Milled/Wavy
Set
(0.031 ")
Apldi.tion
Cuts hall free wood
rough
in work.
Cuts nail free wood
-- rough
in work.
Cuts composition
materials
-
resists
nall damage.
Cuts coml;)Osdion
I_
plywood
-- resist_
nell damage.
Cuts circles and
contours
in nail free
wood,
compo|dionl.
Cutsplaster,
metal
lath, plasterboard,
For cutting
metal
over 1/8"
thick,
For cutting
metal
over 1/8"
thick.
For cutting
metal
over 3164"
thick.
For scroll cuts in
metal
3/64"
thick
and over.
For cutting metal
over 3/64" thick.
For cutting
metal
less than
3/64"
thick.
For cutting
metal
less than 3/64"
thick.
For cutting
metal
less than 1/32"
thick.
Note;
All illustrations
shown are general representations
for blades in that category.
Actual
design of blades may vary slightly.
11
Advertisement
