Advertisement
A
ombination
antenna
receives
normal
broadcast
channels
(VHF
2-13 and UHF 14-69).
Your connection
is easy
since there is only one
75_ (ohm) antenna plug
on the back of your TV-
and that's where the anten-
na goes.
your antenna has a
round cable (75 ohm) on the
end, then you're ready to con-
nect it to the TV.
If your antenna has flat twin-
lead wire (300 ohm), you first
need to attach the antenna wires
to the screws on a 300 to 75
ohm adapter.
Combination
VHF/UHF Antenna
(Outdoor or Indoor)
_Push
the round end of the
adapter (or antenna) onto the
ANTENNA
plug on the rear of
the TV. If the round end of the
antenna wire is threaded, screw
it down tight.
Back Of TV
3_2to
75[2
\\\
I I
II
_
Adapter
\\\
n
It
i
_€
1827003)
Rof
Otwme o f you may have
o separate
antennas.
One antenna
is for VHF
channels
(2-13) and the
other antenna
is for UHF
channels
(14-69).
For homes with separate
UHF/VHF antennas,
you
will need an optional
"combiner"
before you can
connect to the T_. See the
"Smart Help" section
(to
the right on this page) for
ordering details.
_Attach
the separate
Ii_e_and
tVHFan:ent_a Sto°m _
Outdoor UHF Antenna
(Twig-lead 300 Ohm)
Outdoor VHF Antenna
(Twin-lead 300 Ohm)
Outdoor
(Round 75 Ohm cable)
__
•
L
the round end of the
combiner onto the ANTENNA
plug on the rear of the TV.
U/V Combiner
75-300 Ohm Adapter
Back of TV
Round Cable 75_
Remember,
1i
be sure to set the
TV for the type sig-
nal you've connect-
ed (see page 3 of
this Set-Up Guide.)
To set the TV to
select only the
channel numbers in
your area see how
to "Program" or
"Add" channels in
memory on page 3.
To order any
optional accessory
contact your dealer
or call the toll-free
accessory ordering
number (1-800-292-
6066):
• UHF/VHF
Combiner:
(SBV 1133AO 1)
• 75-300 Ohm
Adapter:
(SBV1113AOI)
• 300-75 Ohm
Adapter:
(483521827003)
OUr Cable "IV input into
our home may be a
le (75 ohm) cable, or a
Converter
Box installa-
tion. In either case the
connection
to the TV is
very easy. Just put the
threaded
end of the cable
signal to the TV's antenna
plug and screw it down
tight.
your Cable TV sig-
nal is a single round cable (75
ohm) then you're ready to con-
nect to the TV.
If you have a Cable TV
Converter Box:
Connect the Cable TV signal to
the Cable Signal IN(put) plug
on the Converter.
<
__
Cable TV
cable to the ANTENNA plug
on the TV.
If you have a Cable TV
Converter Box:
Connect the OUT(put) plug
from the Converter to the
ANTENNA plug on the TV
(connecting cable supplied with
the Converter.)
Back of TV
Cable TV Company
Cable 'IV Signal Input
Cable TV Converter
Round Cable
Box Connection
75f_ Ohm
Remember,
set the TV for the
type signal you've
just connected (see
page 3 of this Set-
Up Guide.)
To select only the
channel numbers on
your Cable system
see "Auto Program"
(page 3). If you use
a Cable Converter
box, set the TV to
the same channel as
the converter's CH
3/4 switch (on the
rear of the convert-
er.)
_C
e basic Antenna,
or
able TV, to VCR to
TV connection
is shown to
the right. For more infor-
mation on other hookups
(possible
when Cable
Converter/Descrambler
boxes are included)
refer
to your accessory
VCR
and Cable Converter
Owner's
Manual for
details.
i
i
Connect your
Antenna or Cable TV signal
to the IN FROM ANT(enna)
plug on the VCR.
_Connect
the OUT TO TV
plug on the VCR to the
ANTENNA plug on the TV
(connecting cable supplied
with the VCR.)
Cable TV signal
<
_Refer
to the Owner's
Manual included with your
VCR for other possible con-
nections and TV/VCR operat-
ing details.
Back of TV
Round
Cable
75_
Supplied
with VCR
VCk
Advertisement
