Table of Contents
Advertisement
BALANCE:
Figure 54
phasize the Right Channel (refer to figure 55) or
the Left Channel (refer to figure 56).
BALANCE: 50 dB
Figure 55
BALANCE: 50 dB
¦ ¦¦¦¦ ¦¦¦¦
Figure 56
The Front Panel Display indicates the Balance changes
in steps from 0 to 50dB. After approximately 5 sec-
onds, the Display returns to indicate the Source Selec-
tion and Volume Level. To verify the Balance setting
without changing it, use the TRIM Push-button and
select Balance.
TRIM LEVEL
Source Components can have slightly different volume
levels resulting in the need to readjust the MA5200
Volume Control when switching between different
sources. The MA5200 allows the adjustment of levels
for each of the Source Inputs for the desired same rela-
tive volume. The TUNER and CD Inputs are used in
the following example.
Note: The range of adjustment is ± 6dB. The level
adjustments made are retained in permanent mem-
ory. They can be changed during operation of the
MA5200 by performing a Trim Level Procedure.
1. Press the TUNER Push-button on the Remote
Control and press the VOLume Push-button +/-
for the desired listening level.
2. Repeatedly press the TRIM Push-button on the
0 dB
Remote Control until "TRIM LEVEL: 0.0dB,
Min
||
Refer to figure 57.
Note: The TUNER Input is serving as a reference
¦¦ ¦¦¦¦ ¦¦¦¦
3. Press the CD Push-button on the Remote Control
¦
and note if the relative volume is louder or quieter
than the volume level of the TUNER.
4. Repeatedly press the TRIM Push-button on the
Remote Control until "TRIM LEVEL: 0.0dB,
Min
Refer to figure 57.
5. Press the TRIM LEVEL +/-Push-button on
the Remote Control to achive the same relative
volume as the TUNER Input. In our example the
relative volume level of the CD Input is louder
than the TUNER Input, so the trim level for
the Server Input is reduced to -2.5 dB. Refer to
figure 58.
6. Repeat steps 1 thru 4 until the relative volume is
the same between the TUNER and CD Inputs.
7. Repeat the above steps for the remaining inputs
with component sources connected until they
all have the same relative volume levels. Record
any changes made to the various inputs from the
Max" appears on the Front Panel Display.
level or choose another source frequently
listened to. The Input Source should be set to
a reference Level (Trim) of 0.0dB.
TRIM LEVEL: 0.0 dB
Min
||
Figure 57
Max" appears on the Front Panel Display.
TRIM LEVEL: -2.5 dB
Min
||||||
Figure 58
How to Operate the MA5200
default settings in the "Input and Power Control
Settings" chart on page 19.
After approximately 5 seconds the Display returns to
indicate the Source Selection and Volume Level.
OUTPUT MODE
The OUTPUT MODE default setting for the MA5200
is On. The Power Amplifier Output is then available
at the R&L Output Terminals to drive the connected
Loudspeakers. When it is desireable to switch the
Max
Loudspeakers Off (eg. during listening with head-
phones) set the OUPUT MODE to Off. To switch the
Loudspeaker Off, perform the following steps:
1. Press the TRIM Push-button on the Remote
Control until "OUTPUT MODE, Speaker: On"
appears on the Front Panel Display. Refer to
figure 59.
2. Press TRIM LEVEL + / - Push-button to select the
Off Mode. Refer to figure 60.
Max
After approximately 5 seconds the Display returns to
indicate the Source Selection and Volume Level.
MONO/STEREO MODE
By default the Stereo Mode is active for all Input
Sources however, any Input Source may be assigned
to Mono Mode. To change Stereo Mode to Mono for a
given Input Source, perform the following steps:
OUTPUT MODE
Speakers:
On
Figure 59
OUTPUT MODE
Speakers: Off
Figure 60
23
Hide quick links:
Advertisement
Chapters
Table of Contents
