Marantz NR1604 Owner's Manual page 157

GVideoH
Symptom
No picture appears. • Check the connection between the video output terminal of this
unit and the input terminal of the TV.
• Match the input settings to the input terminal of the TV connected
to this unit.
GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Check the connection with the playback device and select the
proper input source.
• Match the input mode and the terminal assigned to be the digital
input terminal.
• Disconnect the headphones. No sound is output from the
speakers when headphones are connected.
The volume does not • The maximum volume is set too low. Set the maximum volume
increase. using "Limit"on the menu.
• Power for external devices connected to the output connectors
of the unit may not be turned on. Check the power of connected
external devices.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speakers.
No sound is • Check if "Assign Mode" is set appropriately in order to output
produced from audio from the surround back speakers.
surround back • Set "Speaker Config." – "Surr. Back" on the menu to something
speakers. other than "None".
• Set the sound mode to something other than "STEREO" and
"VIRTUAL".
DVD
Cause/Solution
Cause/Solution
9,
15,
19, 20, 21
83, 84, 85,
86, 87, 88,
Symptom
Page
No sound is • Check if "Assign Mode" is set appropriately in order to output
13, 14 produced from front audio from the front height speakers.
height speakers. • Set "Speaker Config." – "Front Height" on the menu to something
other than "None".
–
No sound is • Check the subwoofer connections.
produced from
subwoofer.
Page
• Turn on the subwoofer's power.
1 0, 1 3, 1 4, • Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
1 6, 1 7, 1 8, • If "Front" and "Center" for "Speaker Config." are set to "Large",
and "Subwoofer Mode" is set to "LFE", no sound may be output
from the subwoofers, depending on the input signal or selected
sound mode.
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
89, 90
output.
Dolby TrueHD, DTS- • Make HDMI connections.
–
HD, Dolby Digital
30, 101
Plus audio is not
30, 101
output.
29, 101
• Check that "Speaker Config." – "Center" or "Surround" is set to
Dolby PLg mode or
DTS NEO:6 mode other than "None". If the speaker system is 2.0/2.1-channel, this
122
sound mode cannot be selected.
cannot be selected.
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
138
selected.
Audyssey MultEQ ® ,
• Switch the sound mode to other than "DIRECT" or "PURE
112
Audyssey Dynamic DIRECT".
EQ ® and Audyssey • When headphones are used, Audyssey MultEQ ® , Audyssey
–
Dynamic Volume ® Dynamic EQ ® and Audyssey Dynamic Volume ® cannot be selected.
cannot be selected.
• Run Audyssey ® Setup.
Audyssey Dynamic
–
EQ ® and Audyssey
Dynamic Volume ®
cannot be selected.
124
"M-DAX" cannot be • Check that an analog signal or PCM signal (Sample Rate=44.1/48
selected. kHz) is input. For playback of multichannel signals such as Dolby
124
Digital or DTS surround, "M-DAX" cannot be used.
• Switch the sound mode to other than "DIRECT" or "PURE
72
DIRECT".
154
Cause/Solution
83, 84, 85,
86, 87, 88,
Page
124
124
89, 90
–
124
124, 126
122
9, 10
124
–
72
–
22, 91
111
72