Bluetooth Setup - Kenwood KDC-BT42U Instruction Manual

Bluetooth Setup

Selecting the Bluetooth Device
Press to enter Bluetooth mode.
1
Turn the volume knob to select
2
[SETTINGS], then press to enter.
Turn the volume knob to select
3
[PAIRING], then press to enter.
Turn the volume knob to select [PHONE
4
SELECT]/ [PHONE SEL] or [AUDIO
SELECT]/ [AUDIO SEL], then press to
enter.
Turn the volume knob to select a
5
Bluetooth device name.
Press the volume knob to set up the
6
Bluetooth device.
"✱ (device name)": The selected
■ ■
Bluetooth device is busy.
"- (device name)": The selected Bluetooth
■ ■
device is on standby.
"(blank) (device name)": The Bluetooth
■ ■
device is deselected.
If two cell-phones or an audio player
■ ■
have already been selected, deselect one
device before selecting a new Bluetooth
device.
Hold to finish the procedure.
7
To cancel the Bluetooth mode, press .
■ ■
Bluetooth Device Registration Test
You can check whether your Bluetooth device
can be registered using this unit.
Press and hold to enter pairing mode
1
"PAIRING" is displayed.
"PLEASE PAIR YOUR PHONE" is displayed.
2
When "(device name)" is displayed, select
■ ■
"[PAIRING]" and press the control knob.
When "DEVICE FULL" is displayed, delete a
■ ■
Bluetooth device and retry.
1. Turn the volume knob to select the
Bluetooth device, then press and hold
to confirm.
2. Turn the volume knob to select "YES",
then press to confirm.
20
English
Start registering this unit by operating
3
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit or audio unit (pairing).
Select "KENWOOD BT CD/R-5T1" from the
list of found units.
Input the PIN code ("0000") in the
4
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
"0000" as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page 20).
"(device name)" is displayed. Press and
5
hold the volume knob.
"BT TEST" is displayed.
The connection result, "OK" or "NG", is
6
displayed.
"PAIRING": Registration to this unit
■ ■
"HF CNT": Hands-free phoning
■ ■
"AUD CNT": Audio playback
■ ■
"PB DL": Phone Book downloading
■ ■
Press to exit pairing mode.
7
Data (Phone Book, etc.) of the cell-phone
■ ■
checked for connection does not remain in
this unit.
Bluetooth Setup
Press to enter Bluetooth mode.
1
2 Turn the volume knob to select
[SETTINGS], then press to enter.
Turn the volume knob to make a
3
selection, then press to confirm.
See table below for selection.
■ ■
Repeat step 3 until the desired item is
■ ■
selected/activated.
Press to return to the previous item.
■ ■
Hold to finish the procedure.
4
To cancel the Bluetooth mode, press .
■ ■
Item Selectable setting (Preset: *)
PAIRING
PHONE SELECT/ Selects a cell-phone connection.
PHONE SEL
(For details, see page 20.)
AUDIO SELECT/ Selects a Bluetooth audio player connection.
AUDIO SEL
(For details, see page 20.)
DEVICE DELETE/
Cancel registration of the Bluetooth device.
DVC DELETE 1. Turn the volume knob to select the Bluetooth device, then press to confirm.
2. Turn the volume knob to select "YES", then press to confirm. "DELETE" is displayed.
TRANSFER PB
(For details, see page 18.)
DETAILED SET/
DETAIL SET
PIN CODE EDIT/
Specify the PIN code required when registering this unit using the Bluetooth device. By default, "0000" is
PIN EDIT
specified.
1. Turn the volume knob to select the number.
To move to the next digit, press ¢.
■ ■
To delete the last digit, press 4.
■ ■
2. Press the volume knob to register a PIN code. "COMPLETED" is displayed.
AUTO ANSWER OFF: Does not answer the phone call automatically. ; 0: Automatically answers the phone call at once. ;
1 – 8 * –99: Automatically answers the phone call after lapse of 1 – 99 seconds.
RECONNECT/ ON *: Automatically reconnects the selected Bluetooth device when radio wave becomes strong enough,
RECONCT even after it is disconnected. ; OFF: Cancels.
When this function is turned ON, the Bluetooth device is reconnected if it has been disconnected by
■ ■
selecting [PHONE SELECT]/ [PHONE SEL]/ [AUDIO SELECT]/ [AUDIO SEL].
BT HF/AUDIO FRONT *: Outputs audio from the front-left and front-right speakers. ;
ALL: Outputs audio from the all speakers.
CALL BEEP ON *: Sets whether to output a beep from the speaker when a call comes in. ; OFF: Cancels.
BT F/W UPDATE/ Display the firmware version and update the firmware.
BT UPDATE
MIC GAIN 1 — 8 * — 15: Adjust the sensitivity of the microphone for telephone call or adjusts the voice of the caller.
(KDC-BT42U: The default is 12 when [MIC SELECT] is set to [EXT].)
MIC SELECT
KDC-BT42U only
Determines whether the built-in or external microphone is to be used when the receiver incorporates a
microphone. IN *: Use the built-in microphone. ; EXT: Use the external microphone.
CONTENTS
21
English