Technical Specifications; Conformity Certificates; Technical Data; Ec Declaration Of Conformity - Husqvarna Soff-Cut 4200 Operator's Manual

Engine
Model Kohler Command Pro CH22S
Engine oil volume, 2/1.9
quarts/liters
Gasoline tank 33.0/11
volume, gal/liters
Type Air cooled, 4-cycle, twin cylinder, hydrau-
lic overhead valves, gasoline engine
Air fi lter Tri phase remote mount canister style
Oil system Full pressure lubrication with spin-on oil
fi lter
Muffl er Low noise, side exhaust
Emissions Complies with EPA Phase 2 and CARB
Tier II USA regulations
Cooling Air cooled
Cylinder Aluminum with cast iron liner
Controls nstrument panel mounted manual choke,
electric switch operated throttle, keyed
on/off switch
Weight and Dimensions
Weight – dry, lbs/kg
Weight with gasoline and oil full, lbs/kg
Length (handle folded in), inch/mm
Width, inch/mm
Height, inch/mm
Blade
Material cut Green concrete only
Blade type 13.5" (343 mm) or 12.0" (305 mm) dry
cut with tri-arbor
Blade rotation Counter clockwise, upcutting
CALIFORNIA AIR RESOURCES BOARD (CARB): This machine is considered a preempt Off-Road Application as relating to CARB stan-
dards. Under construction equipment, and in particular, as a Saws : concrete, masonry, cutoff, with engine power less than 19KW (25hp),
CARB standards do not apply to this machine.
For more information see the website

EC DECLARATION OF CONFORMITY

Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 4200
dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with
the requirements of the COUNCILíS DIRECTIVE:
• of May 17, 2006 "relating to machinery" 2006/42/EC
• of December 15, 2004 "relating to electromagnetic compatibility" 2004/108/EC.
• of May 8, 2000 "relating to the noise emissions in the environment" 2000/14/EC.
The following standards have been applied: EN ISO 12100:2003, EN 55014-1:2006, EN 55014-2/A1:2001, EN 61000-3-2:2006, EN 61000-
3-3/A1/A2:2005, EN 13862/A1:2009.
Huskvarna December 29, 2009
Henric Andersson
Vice President, Head of Power Cutters and Construction Equipment
(Authorized representative for Husqvarna AB and responsible for technical documentation.)

TECHNICAL SPECIFICATIONS

472/214
496/225
59/1499
30/762
38/965

TECHNICAL DATA

http://www.arb.ca.gov/msprog/offroad/preempt.htm
Blade shaft speed, 3500
rpm
Cutting depth 3 inch maximum (76 mm) depending on
blade size and amount of blade wear
Cutting distance 3 1/2 / 89
from wall, inch/mm
Average cutting rate - Estimate only. Speed will vary with job
conditions and concrete mixes.
Soft aggregates, ft/min / m/min
Medium aggregates, ft/min / m/min
Hard aggregates, ft/min / m/min
Blades are available in 13.5 inch (343 mm) and 12 inch (305 mm)
diameters and in 0.100 inch (2.5 mm), 0.250 inch (6.4 mm), 0.380
inch (9.7 mm), and 0.500 inch (12.7 mm) widths.
Noise emissions (see note 1)
Sound power level, measured dB(A)
Sound power level, guaranteed dB(A)
Sound levels (see note 2)
Sound pressure level at the operators ear, dB(A)
Vibration levels, a (see note 3)
hv
Handle right, m/s
2
Handle left, m/s
2
Note 1: Noise emissions in the environment measured as sound
power (L ) in conformity with EC directive 2000/14/EC.
WA
Note 2: Noise pressure level according to EN 13862. Reported
data for noise pressure level has a typical statistical dispersion
(standard deviation) of 1.0 dB(A).
Note 3: Vibration level according to EN 13862. Reported data for
vibration level has a typical statistical dispersion (standard devia-
tion) of 1 m/s .
2
3 inch (76 2 inch (51
mm) depth mm) depth
16/4.9 26/7.9
12/3.7 18/5.5
8/2.5 10/3.0
105
106
91
3,4
3,6