Table of Contents
Advertisement
Available languages
Available languages
Delay start
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown.
After adding items, close the door firmly until it
latches. The delay countdown will not continue if the door is not
latched. Press START/RESUME. If the door is unlatched, the
Start/Resume
indicator flashes. The delay countdown
stops until
you latch the door and press START/RESUME.
Models with 4 Hour Delay
To delay the start
1. Press DELAY for a 4-hour delay. The number above or to the
left of the 4 Hour Delay pad glows.
2. Select a wash cycle and option or skip to Step 3 to use the
cycle and options selected for last cycle.
3. Press START/RESUME. (The door must be closed.) The delay
countdown
starts, and the cycle will begin after 4 hours.
NOTES:
•
To cancel the delay and cycle, press CANCEL/DRAIN.
•
To cancel the delay and start the cycle, press START/
RESUME.
Models with 2-4-6 hour Delay
To delay the start
1. Press DELAY 1 time for a 2-hour delay, 2 times for a 4-hour
delay, or 3 times for a 6-hour delay. The number glows above
the Delay pad.
2. Select a wash cycle and option or skip to Step 3 to use the
cycle and options selected for last cycle.
3. Press START/RESUME. (The door must be closed.) The Delay
countdown
starts, and the cycle will begin after the selected
number of hours.
NOTES:
•
To cancel the delay and cycle, press CANCEL!DRAIN.
•
To cancel the delay and start the cycle, press START/
RESUME.
Follow the progress of your dishwasher with the Cycle Status
indicators.
Sensing Washing Drying
Clean Sanitized
NOTE: Your model may have some or all of the indicators shown
above.
Sensing (on some models)
Sensing glows during the Sensing part of the cycle. Your
dishwasher senses soil level during soil sensing intervals and
water temperature
during water heating pause intervals.
Washing continues while Sensing occurs.
Clean
Clean glows when a cycle is finished. The light turns off when you
open and close the door or press any button.
Sanitized
If you select the SANI RINSF M option, Sanitized glows when the
SANI RINSE
TM
cycle is finished. If your dishwasher did not
properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted,
or the water
could not be heated to the required temperature.
The light goes
off when you open and close the door or press any button.
During drying, you can see steam escaping through the vent at
the upper left corner of the door. This is normal as the heat dries
your dishes.
IMPORTANT: The vapor is hot. Do not touch the vent
during drying.
Models DU1200, DU1201, DU1245, and DU1248 are equipped
with an optical sensor wash that detects water temperature,
soil
and detergent amount. Wash cycles are adjusted based on what
is sensed.
The dishwasher
"senses" wash water quality during a series of
pauses in the wash cycle. The sensor monitors water
temperature and the amount of soil and detergent appearing in
the wash water. It automatically
adjusts the wash cycle for the
best wash. Lightly soiled dishes will use less water and energy.
Heavily soiled dishes will get more water and increased
temperature and wash time. This dishwasher will automatically
adjust the sensor approximately
once a year to your water
quality.
IMPORTANT: The very first wash cycle after installation in your
home will be adjusted to include an additional 2 rinses. This cycle
must not be interrupted for proper sensor adjustment.
If this
adjustment cycle is canceled or stopped before the Clean light
comes on at the end of the cycle, the next wash cycle will repeat
this sensor adjustment.
The overfill protection float (in the front right corner of the
dishwasher tub) keeps the dishwasher from overfilling. It must be
in place for the dishwasher to operate.
Check under the float for objects that may keep the protector
from moving up or down.
15
Advertisement
Table of Contents
