Griddle Grate (On Some Models); Ovenuse; Electronic Oven Controls - Whirlpool GFG474LVS1 User Instructions

4. Replace theburner cap, m aking s ure thealignment pins are
properly aligned w iththeburner cap.
( t;
5=
A. Incorrect
B. Correct
Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, do not service the
sealed burner yourself. Contact a trained repair specialist.
IMPORTANT: Do not use the griddle grate while using the Self-
Clean mode.
A. Griddle grate installed on right side of cooktop
To Use the Griddle Grate:
1. Remove the right side grate from the cooktop and replace it
with the griddle grate.
2. Before each use, brush on a thin layer of cooking oil to keep
food from sticking. Cooking sprays may leave a sticky residue
on the griddle that is hard to remove.
3. Preheat the griddle for 5 minutes. Preheating the griddle slowly
will ensure even heat distribution and will avoid warping the
griddle.
4. For preheating and cooking, set the front burner to the lowest
heat setting and the rear burner to medium or medium high
heat for best performance.
To Clean the Griddle Grate:
1. Let the griddle cool, then empty the grease tray.
2. See the "General Cleaning" section for cleaning instructions.
3. Store griddle in a cool dry place.
OVENUSE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
Control Display
The display will flash when powered up or after a power loss. Press
CANCEL/OFF to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.
Tones
Tones are audible signals, indicating the following:
One tone
• Valid pad press
• Oven is preheated (long tone)
• Function has been entered
• Reminder (on some models), repeating each minute after the
end-of-cycle tones
Three tones
• Invalid pad press
Four tones
• End of cycle
To Change Tone Settings:
Tone Pitch
Sets the pitch of the tone to either high or low.
Press and hold BROIL for 5 seconds. "TONE PITCH HIGH" or
"TONE PITCH LOW" will appear in the display. Press and hold
BROIL again to change setting.
To exit, press CANCEL!OFE
Key Press Tones
Activates or turns off the tones when a keypad is pressed.
Press and hold KEEP WARM for 5 seconds. "KEY PRESS TONES
ON" or "KEY PRESS TONES OFF" will appear in the display. Press
and hold KEEP WARM again to change setting.
To exit, press CANCEL!OFE
End of Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
Press and hold CONVECT for 5 seconds. "CYCLE END TONE ON"
or "CYCLE END TONE OFF" will appear in the display. Press and
hold CONVECT again to change setting.
To exit, press CANCEL!OFE
Reminder Tones Disable
Turns off the short tones that sound 1 minute after the end of cycle
tones.
Press and hold BAKE for 5 seconds. "REMINDER TONES ON" or
"REMINDER TONES OFF" will appear in the display. Press and
hold BAKE again to change setting.
To exit, press CANCEL!OFE
Audible Tones Disable
Turns off all tones, including the end of cycle tone and key press
tones. Reminder tones are still active when all tones are disabled.
Press and hold CLOCK for 5 seconds. "ALL SOUNDS ON" or "ALL
SOUNDS OFF" will appear in the display. Press and hold CLOCK
again to change setting.
To exit, press CANCEL!OFE
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius.
To change: Press and hold PRECISE CLEAN for 5 seconds. A tone
will sound, and "°C" or "°F" will appear on the display. Repeat to
change back.
To exit, press CANCEL!OFE