Related Manuals for Troy-Bilt TBHS
Summary of Contents for Troy-Bilt TBHS
- Page 1 ® Operator's Manual Hedge Trimmer TBHS IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY SOUTHWEST INC, Chandler, AZ 85226-2434 769-00417 (8/02) PRINTED IN USA...
- Page 2 E. Transporting ......Copyright © 2002 MTD SOUTHWEST INC F. Accessories/Replacement Parts .... All Rights Reserved. Troy-Bilt® is a registered trademark of IV. Specifications ......MTD PRODUCTS INC SERVICE INFORMATION V. Warranty ........
- Page 3 The purpose of safety symbols is to attract your attention to DANGER: Failure to obey a safety warning will )ossible dangers. The safety symbols, and their result in serious injury to yourself or to others. explanations, deserve your careful attention and Always follow the safety precautions to reduce understanding.
- Page 4 • OTHER SAFETY WARNINGS Always hold the unit with both hands when operating. Keep a firm grip on both the front and rear handle or grips. • Keep hands, face, and feet at a distance from all moving parts. Do not touch or try to stop the blades when they are moving. is in the 'off, position.
- Page 5 SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution.
- Page 6 APPLICATIONS With Hedge Trimmer Add-On: • Trimming hedges and shrubs, Shaft Housing_ Hanger _ Loop Handle ___= \\\\ Blades Housing...
- Page 7 ASSEMBLING THE COUPLER NOTE: Aligning the release button with the guide recess will help installation (Fig. 1). The following Troy-Bilt Add-Ons are also available for your unit: Release Button Coupler Blower/Vacuum ......TBBV Primary Hole Cultivator ........ TBGC Edger ........
- Page 8 PREPARING FOR OPERATION OPERATING TIPS For ease of operation, your hedge trimmer has a loop NOTE: Do not operate unit with the hedge trimmer handle. For ease of operation and best balance of the attachment at full engine speed. Best unit.
- Page 9 IMPORTANT! Align the cams (Fig. 9). Remove the four (4) blade screws (Fig. 9). Lubricating Cams Blade Screws The cams are lubricated with a sufficient amount of high- temperature grease. To keep the attachment operating efficiently, apply a high-temperature grease to the cams, and in between the yokes every 6 hours of use.
- Page 10 7. Squeeze theyokesandremove thebladefromthe WARNING: When Servicing, use only housing (Fig.12). identical OEM replacement parts. Use of any I I other parts may create a hazard or cause LPrOdUCt damage. Housing Slot Fig. 12 INSTALLING BLADE Bottom Plate Fig. 14 LUBRICATING BLADE blade assembly, do not place your hand or...
- Page 11 ACCESSORIES/REPLACEMENT PARTS STORAGE Replacement Blade ....791-181660 • Check unit before storage to be sure the equipment is in safe working condition. Blade Screws (4 required) ....791-181827 • Stop the engine or motor. Loop Handle Assembly ....791-180869 Handle Mounting Hardware •...
- Page 12 REPLACEMENT PARTS - MODEL TBHS HEDGE TRIMMER ADD-ON PPN 41AJHS-C063 Item Part No. Description 791-181070 Screw 753-1220 Drive Shaft Housing Assembly 791-180869 Loop Handle Assembly 791-181840 Drive Shaft Assembly 753-1219 Housing Set 791-181629 Anti-Rotation Screw 791-181843 191-181844 Housing Screw 791-181851 Insulator 791-181846 Bevel Gear Assembly...
- Page 13 MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt No implied warranty, including any implied warranty LLC with respect to new merchandise purchased and of merchantability or fitness for a particular purpose, used in the United States, its possessions and territories.