Watching Tv; Turning On The Power; Auto Setup; Select The Tv Mode - Sharp AQUOS LC-32DV28UT Operation Manual

=20
Watching TV
Preparation Select the TV mode
Perform the following steps before you press POWER
on the remote control unit.
1 Insert the batteries into the remote control unit.
(See page 10.)
2 Connect the antenna cable to the TV/DVD. (See
page 14.)
3 Plug in the AC cord to the AC outlet. (See page 9.)
Press TV/DVD to select the TV mode.
Turning off the power
Press POWER on the TV/DVD, or POWER on the
remote control.
• The TV/DVD enters standby mode and the image on the
screen disappears.
The POWER indicator on the TV/DVD changes to Red.
Turning on the power
,, If you are not going to use this TV/DVD for a long period
Press POWER on the TV/DVD, or POWER on the of time, be sure to remove the AC cord from the power
outlet.
remote control. , Weak electric power is still consumed even when the
TV status indicator (POWER) power is turned off.
ON Lighting (Green)
OFF/Standby Lighting (Red)
,, POWER indicator (Green): The TV/DVD is on. ("Please
wait" will appear for a few seconds on the screen.)
Auto Setup
changing
You can change channels in several ways.
Method 1
Using CH /,./v on the remote control unit or on the
TV/DVD.
The Auto Setup menu appears the first time you turn
on the TV/DVD, and assists you to select the menu
language, specify the Air/Cable setting, and program
your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV
system connection is made!
1 The turn on the TV/DVD, press POWER (POWER
indicator on the front of the unit changes green. It may
take approx. 10 seconds for a picture to appear on
screen.).
2 The "Auto Setup" function begins. Press _/_ to select
your desired language.
3 Press A/T to select"TV Location", then press _/_
to select "Home" or "Store". This product qualifies for
ENERGY STAR in Home mode default setting.
Home: Qualifies for ENERGYSTAR (Backiight: Default setting)
Store: Not qualify for ENERGYSTAR (Backlight:maximum)
,, If you want to change this setting, you can adjust the
"Backlight" setting. (See page 28.)
4 Press A/T to select"SignalType", then press _/_ to
select "Cable" or "Air".
Air: VHF/UHF channels
Cable: CABLETV channels
5 Press A/T to select"Automatic Search", then press _ or
ENTER.
The TV will begin memorizing all the channels available
in your area.
,, It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a bar display may
not advance for several minutes, please be patient.
,, If you press ENTER in the process of "Auto Setup", the
Auto Setup stops and changes to the normal screen.
,, When you make a menu selection, your changes occur
immediately.You do not have to press EXIT to see your
changes.
,, If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
If you use channel-down, it will move in reverse, from the
digital channel to the analog channel.
Method 2
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CATV/DIGITAL
To select a 1 or 2-digit channel number (e. g., Channel 5):
Press 5
,, When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
,, When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
To select a 3-digitchannel number (e. g., Channel 115):
Press 1->1->5
To select a 4-digit channe! number (e. g., Channel 22.1):
Press 2->2-> = (DOT) ->1
,, When you enter 0-9 only, channel selection will be made
if there is no operation within a few seconds.
,, If you press 0 by itself in "Air" reception, nothing will
happen.
,, Complete the above steps within a few seconds.
,, When you enter 0-9 and • (DOT), channel selection will
be made if there is no operation within a few seconds.