Table of Contents
Advertisement
Watching TV
Perform the following steps before you press POWER
on the remote control unit.
1 Insert the batteries into the remote control unit.
(See page 10.)
2 Connect the antenna cable to the TV/DVD. (See
page 14.)
3 Plug in the AC cord to the AC outlet. (See page 9.)
Press TV/DVD to select the TV mode.
Press POWER
on the TV/DVD,
or POWER
on the
remote control.
• The TV/DVD enters standby mode and the image on the
screen disappears.
• The POWER indicator on the TV/DVD changes to Red.
Press POWER
on the TV/DVD,
or POWER
on the
remote control.
TV status
indicator
(POWER)
ON
Lighting (Green)
OFF/Standby
Lighting (Red)
• POWER indicator (Green): The TV/DVD is on. ("Please
wait" will appear for a few seconds on the screen.)
The Auto Setup menu appears
the first time you turn
on the TV/DVD,
and assists you to select the menu
language,
specify the Air/Cable
setting,
and program
your channels
automatically.
IMPORTANT:
Make sure that the antenna
or cable TV
system
connection
is made!
1
The turn on the TV/DVD, press POWER (POWER
indicator on the front of the unit changes green. It may
take approx. 10 seconds for a picture to appear on
screen.).
2
The "Auto Setup" function begins. Press ,/_ to select
your desired language.
Press A/T to select "Signal Type", then press ,/_
to
select "Cable" or "Air".
Air:
VHF/UHFchannels
Cable: CABLETV channels
4
Press A/T to select "Automatic Search", then press _ or
ENTER.
The TV will begin memorizing all the channels available
in your area.
• It may take from 15 minutes to 30 minutes to complete
memorizing digital cable channels.
Depending on the reception condition, a bar display may
not advance for several minutes, please be patient.
• If you press ENTER in the process of "Auto Setup", the
Auto Setup stops and changes to the normal screen.
• When you make a menu selection, your changes occur
immediately. You do not have to press EXIT to see your
changes.
• If you are not going to use this TV/DVD for a long period
of time, be sure to remove the AC cord from the power
outlet.
• Weak electric power is still consumed even when the
power is turned off.
You can change channels
in several
ways.
Method
1
Using CH /,,/v
on the remote control unit or on the
TV/DVD.
• If your cable-TV system includes analog and digital
channels using the same channel number, your channel
up function will scroll through the analog channel first,
then the digital channel. Although it may appear as though
the channel does not change, it actually moves from the
analog to the digital channel in sequence.
If you use channel-down,
it will move in reverse, from the
digital channel to the analog channel.
Method 2
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CATV/DIGITAL,
then press
ENTER.
To select a I or 2-digit channel number (e. g., Channel 5):
Press 5
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection wil! be made
if there is no operation within a few seconds.
To select a 3-digit channelnumber (e. g., Channel 115):
Press 1-->1-->5
To select a 4-digit channelnumber (e. g., Channel 22.1):
Press 2-->2-->° (DOT) -->1
• When you enter 0-9 only, channel selection wil! be made
if there is no operation within a few seconds.
• If you press 0 by itself in "Air" reception, nothing wil!
happen.
• Complete the above steps within a few seconds.
• When you enter 0-9 and • (DOT), channel selection will
be made if there is no operation within a few seconds.
(_=
20
Advertisement
Table of Contents
Troubleshooting
