Page 2
Use the cursor keys (A/_) to select an item and press ENTER. You can change the settings of the sound programs and surround decoders using the TV screen. Press ON SCREEN. Use the cursor keys to select "Sound Program" and press ENTER. •...
Page 3
Sound Program menu items Adjusts the delay between the direct 0 ms _ 250ms Reverb Delay sound and rear reverberant sound Higher to enhance the delay generation, effect and lower to reduce. • Available items vary depending on the selected sound program or surround decoder. 0% _ 100% Reverb Level Adjusts...
Page 4
@ Settings for decoders The following items are available when you set "Decode Type" of "Surround Decoder" to "PLIIx Music" or "Neo:6 Music". off (default), Adjusts the broadening Select "On" to wrap front right/left channel sounds around the field Panorama effect of the front sound and generate a spacious...
Page 5
Use the cursor keys to select a setting and press ENTER. You can configure the various functions of this unit using the TV screen. To exit from the menu, press ON SCREEN. Press ON SCREEN. Use the cursor keys to select "Setup" and press ENTER.
Page 6
Setup menu items Auto Setup Optimizes the speaker settings automatically (YPAO). Power Amp Assign Selects a speaker system. Front Selects the size of the front speakers. Center Selects whether or not a center speaker is connected and its size. Surround Selects whether or not surround speakers are connected and its size.
Page 7
Max Volume Sets the Zone2 maximum volume so that sound is not too loud. Zone2 Set Multi Zone Initial Volume Sets the Zone2 initial volume for when this unit is turned on. Zone Rename Changes the zone names displayed on the TV screen. Auto Power Down Sets the amount of time for auto-standby.
Page 8
Configuration Speaker (Manual Setup) Configures the output characteristics of the speakers. Configures the speaker settings manually. • When you configure the speaker size, select "Large" if the woofer diameter of your speaker is 16 cm or larger or "small" if it is smaller than 16 cm. [_ Front Selects the size of the front speakers.
Page 9
17 Surround Back [_ Extra Bass Selects whether or not surround back speakers are connected and its size. Sets the speakers to produce the front channel low-frequency components. Settings Settings Select this when 1 large speaker is connected. Off (default) Depending on the size of the front speakers, either the subwoofer Large xl...
Page 10
Level Manual equalizer adjustment Set "PEQ Select" to "Manual" and press ENTER. Adjusts the volume of each speaker. Use the cursor keys to select a speaker and press ENTER. Choices Use the cursor keys to select an item and press ENTER. Front L, Front R, Center, Surround L, Surround R, Surround...
Page 11
Sound Dynamic Range Selects the dynamic range adjustment method for bitstream audio (Dolby Digital Configures the audio output settings. DTS signals) playback. Settings Maximum (default) Produces audio without adjusting the dynamic range. Standard Optimizes the dynamic range for regular home use. Sets the dynamic range to make clear sound even at night or at low volumes.
Page 12
Video @ Processing Enables/disables the video signal processing (resolution and aspect ratio). Configures the video output settings. Settings Off (default) Disables the video signal processing. Enables the video signal processing. Select a resolution and an aspect ratio in "Resolution" and "Aspect". •...
_l ARC HDMI Enables/disables (p.21) when "HDMI Control" is set to "On". Configures the settings related to HDMI. Settings Disables ARC. On (default) Enables ARC. • You do not need to change this setting normally. In case noises are produced from the speakers connected to this unit because...
Page 14
Standby Through 17 Manual Setup Configures the network parameters of this unit manually when "DHCP" is set to "Off". Select whether to output videos/audio (input through HDMI jacks) to the TV when this unit is in standby mode. Submenu Settings IP Address Specifies an IP address.
Page 15
Multi Zone Zone Rename Changes the zone names displayed on the TV screen. Configures the multi zone settings. Setup procedure Use the cursor keys to select a zone to be renamed and press ENTER. Press ENTER, use the cursor keys to rename, and then press ENTER again.
Page 16
Display Trigger Output Configures the settings related to the front display and TV screen display. Sets the TRIGGER OUT jack to function synchronized with power status of each zone or input switching. _] Front Panel Display rl Trigger Mode Configures the front display settings.
Page 17
[_Target S ource Language Specifies the output level of the electronic signal transmitted with each input switching Select an on-screen menu language. when "Trigger Mode" is set to "Source". Choices HDMI1-5, AV1-6, V-AUX, AUDIO1-2, TUNER, Sirius Satellite Radio, (network sources), USB, DOCK Settings...
Page 18
Types of information Audio Signal You can view information about this unit using the TV screen. Displays information about the current audio signal. Press ON SCREEN. Format Audio format of the input signal Use the cursor keys to select "Information" and press ENTER.
Page 19
HDMI Monitor Displays information about the TV connected to the HDMI OUT jack. Interface TV interface You can configure the system settings of this unit using the front display. Video Resolution Resolutions supported by the TV Set this unit to standby mode. N Network While holding down STRAIGHT on the font panel, press MAIN ZONE (l_.
Page 20
Select the remote control ID of the main unit so that it matches to the ID of the remote control (default: ID1). When using multiple Yamaha AV receivers, you can set each remote control with a unique remote control ID for its corresponding receiver.
Page 21
Removing the limitation on HDMI video output Updating the firmware (UPDATE) (MON.CHK) New firmware will be released irregularly for the purpose of additional features or product improvements. It can be downloaded from our website. If this unit is connected to the Internet, you can download the firmware via the network. For details, refer to the information supplied with updates.
Page 22
By setting the code for external devices (BD/DVD players, etc.), Press TV _) you can operate it with the remote control of this unit. Use the numeric keys to enter the 4-digit remote control code. • You cannot control an external device that does not have a remote control...
Page 23
For example, if you register the remote control code of your external device on TUNER, you can operate FM/AM radio built in this unit when SOURCE/ • At the factory, Yamaha CD player code (5095) is set for AV3. For the other...
Page 24
Resetting remote control codes You can clear all remote control codes and restore the default settings. Press CODE SET using a pointed object such as the tip of a ballpoint pen. SOURCE/RECEIVER blinks twice. Perform each of the following steps within 1 minute. Otherwise, the setting will be canceled.
Page 25
If this unit is connected to the Internet, the corresponding message will be displayed on the TV when a newer firmware is available. this case, follow the procedure below to update the firmware of this unit. Not¢_ icon • Do not operate this unit or disconnect the power cable or network...
Page 26
When using multiple Yamaha products, the supplied remote control may work on another Yamaha product or another remote control may work on this unit. In this case, all... set each remote control with a unique remote control ID for its corresponding receiver To use HDMI Control, you need to perform the HDMI Control link setup (p.121 ).
Page 27
The protection circuitry has been activated 3 times consecutively, nearest Yamaha dealer or service center to request repair. The internal microcomputer is hung-up due to an external electric Hold down MAIN ZONE (.!) on the front panel for more than 10 seconds...
Page 28
Audio Another input source is selected. Select an appropriate input source with the input selection keys Some digital audio formats cannot be played back on this unit. To check the No sound. Signals that this unit cannot reproduce are being input. audio format of the input signal, use "Audio Signal"...
Page 29
(If the TV is connected to this unit with an audio cable) Use "TV Audio Input" in the "Setup" menu to select the correct audio input jack The TV audio input setting does not match the actual connection. (p.95). No sound from the TV (when HDMI Control is used).
Page 30
FM/AM radio There is muki-path interference. Adjust the FM antenna height or orientation, or place it in a different location. Press MODE to select monaural FM radio reception (p.45). FM radio reception is weak or noisy. Your area is too far from the FM station transmitter. Use an outdoor FM antenna commercially available.
Page 31
files in the PC cannot be viewed Use the file format supported by both this unit and the media server. For played back. The files are not supported by this unit or the media server, information about the file formats supported by this unit, see "Playing back music stored on PCs"...
Page 32
Access denied Access to the PC is denied. Configure the sharing setting and select this unit as a device to which music contents are shared (p.64). This unit cannot access the USB device. Turn off this unit and reconnect your USB device. If the problem persists, try another USB device.
Page 33
Error indications for SIRIUS Satellite Radio Adjust the orientation of the antenna of the SiriusConnect tuner by checking the antenna reception level ACQUIRING SIG The signal is too weak. displayed in the front display (p.51) or TV (p.51). ANTENNA ERROR The antenna is not connected to the SiriusConnect...
Page 34
Use this diagram as guide. You do not need to adjust the speaker layout to the following diagram exactly. 0.5 tolm 0.5 tolm 1'8m i i(5.9 ft) (5,9 ft) i Turn it slightly inward to reduce wall reflections. Front speaker (L) Front speaker (R) Center speaker Surround speaker...
Page 35
2 flont left Based on a wealth of actually measured data, Yamaha CINEMA DSP uses Yamaha's original DSP technology combine Dolby Pro Logic, Dolby Digital, and DTS systems to provide the audiovisual experience...
Page 36
DTS Digital Surround. SILENT CINEMA Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones Direct Stream Digital (DSD) technology stores audio signals on digital storage media, such as Super Audio CDs.
Page 37
Video information Component video signal With the component video signal system, the video signal is separated into the Y signal for luminance and the Pb and Pr signals for chrominance. Color can be reproduced more faithfully with this system because each of these signals is independent.
Page 38
@ Video conversion table Video signal flow Video signals input from a video device to this unit are output to a TV as shown below. • You can select a resolution and an aspect ratio applied to HDMI-output video processing. _(solid line) is always available, ooo_(dotted line) is...
Page 39
To use HDMI Control, you need to perform the following HDMI Control link setup after connecting the TV and playback devices. HDMI Control • This setup is required every time when you add a new HDMI Control-compatible device to your system. HDMI Control allows you to operate external devices via HDMI.
Page 40
HDMI signal compatibility Audio signals 2ch Linear PCM 2ch, 32 to 192 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio DVD-Audio, BD (Blu-ray disc), Multi-channel Linear PCM 8ch, 32 to 192 kHz, 16/20/24 bit HD DVD 2/5.1ch, 2.8224 MHz, 1 bit SACD Bitstream Dolby Digital, DTS DVD-Video...
Page 42
IIS and Thomson. _Netwetk This receiver supports network connections. Bluetooth Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement. Hnil'lll "HDMI," the "HDMI" logo and "High-Definition Multimedia Interface" are trademarks,...
Page 43
TUNER - Composite Input jacks AV OUT • Analog Audio • Analog Tuner - Composite [U.S.A. and Canada models] [U.K. and Europe models] • HDMI Output Audio x 5 (AV5-6, AUDIO1-2, V-AUX) FM/AM with RDS x 1 (TUNER) HDMI OUT x 1 [Other models] [Other models] Audio x 6 (AV5-6,...
Page 44
Audio Section Treble Turnover ............. 3.5 kHz • Frequency Response AV5 etc. to Front (10 kHz to 100 kHz) ......+0/-3 dB • Filter Characteristics • Rated Output Power • RIAA Equalization Deviation (fc =40/60/80/90/100/110/120/160/200 (20 Hz to 20 kHz, 0.09% THD, 80-) Front L/R ..............
Page 45
FMSection • Maximum Power Consumption [Asia and General models] ..........590 W • Tuning Range • Dimensions (W x H x D) ......435 x 161 x 363 mm [U.S.A. and Canada models] ....87.5 MHz to 107.9 MHz (17-1/8" x 6-3/8" x 14-1/4") [Asia and General models] ........
Page 47
Supplement for Pandora The Pandora service is available in the U.S.A. only. Press NET repeatedly to select "Pandora" Perform the following procedure. as the input source. Pandora is a free, personalized Internet radio service If you select "YES" in step 4 playing only music you love.
Page 48
If you select "NO" in step 4 Perform the following procedure. ,1, Write down the URL and active code shown in the • If playback of any Pandora station is ongoing, the playback If both artists and songs are found screen is displayed.
Page 49
Playback of Pandora stations If you have created Pandora stations, follow the • You can register your favorite Pandora station as shortcuts procedure below to select a Pandora station to be and access them directly by selecting the shortcut numbers. Creates a new Pandora station.
Page 51
ENTER. from any device including this unit. the sign-in screen appears when you select "Napster". Napster is the ultimate music service for your Yamaha, Use the cursor keys (_/v) to select "Sign To start using the Napster service on this unit, follow the...
Page 52
Browse screen Use the cursor keys and ENTER to enter Select a song from the playlists you have your password and select "OK". My Napster created online. The following screen appears if you have Select a song or a Napster radio station from successfully logged into your account.
Page 54
Supplement for Rhapsody Rhapsody ° account sign-in The Rhapsody (eservice is availablein the U.S.A.only. Use the cursor keys and ENTER to enter If you have not signed in to your Rhapsody account yet, your user name and select "OK". the sign-in screen appears when you select "Rhapsody".
Page 55
Use the cursor keys to select an item and Item number/total Playback of Rhapsody ° contents press ENTER. Operation menu Follow the procedure below to operate the Rhapsody If a song or a radio channel is selected, playback Use the cursor keys to select an item and press ENTER to contents and start playback.
Page 57
Supplement for SIRIUS Internet Radio Press NET repeatedly to select "SIRIUS Use the cursor keys and ENTER to enter The SIRIUS Internet Radio service is available in the U.S.A. only. (Service not available in Alaska and Hawaii) your user name and select "OK". In"...
Page 58
Browse screen @ Playback screen Playback of SIRIUS Internet Radio contents Follow the procedure below to operate the SIRIUS Internet Radio contents and start playback. Press NET repeatedly to select "SIRIUS IR" as the input source. The browse screen is displayed on the TV. Playback indicator Playback indicator @ List name...
Page 60
@YAMA English This product uses the following free software. For information (copyright, etc) about each software, read the original sentences stated below. library. If you use our work, you ought to acknowledge There is no warranty that our efforts or the library will About The Independent JPEG...
Page 61
List of remote control codes Lista de codigos de mando a distancia Liste des codes de commande Lijst met afstandsbedieningscodes Liste der Fernbedienungscodes ynpaBneHH_ Ct3HCOK KO_OB _HCTaHU, HOHHOFO Lista 6ver fj_irrstyrningskoder Elenco dei codici di telecomando Alntron OO58 Baur 0320, 0349 Cathay 0320, 0349, 0350...