Table of Contents
Advertisement
Advanced Features
Listening through a Receiver
You can listen to sound through
a receiver (i.e Home Theater)
instead
of the IV
Speaker.
1.
Select
Receiver
and set to On.
2.
Press the EXIT button
to exit.
if your receiver
supports
audio
only, it may not appear
in the device
list.
The receiver
will work when you have properly
connected
the optical
in jack
of the receiver
to the DIGITAL
AUDIO
OUT (OPTICAL}
jack of the TV.
* When
the receiver
(i,e Home Theater)
is set to On, you can hear sound
output
from the TV's Optical
jack. When
the TV is displaying
a DTV (air) signal, the TV will send out 5.1 channel
sound
to the receiver.
When the source
is a digital
component
such as a DVD and is connected
to the TV via HDMI, only 2 channel
sound will be heard
from the receiver.
NOTE
* You can only control
Anynet+
devices
using the TV remote
control,
not the buttons
on the TV,
* The TV remote
control
may not work
under
certain
conditions,
If this occurs,
reselect
the Anynet+
device.
* The Anynet+
functions
do not operate
with other
manufacturers'
products.
Troubleshooting for Anynet+
Anynet+ does not work.
Iwant to start Anynet+.
Iwant to exit Anynet+.
The message "Connecting to
Anynet+ devbe..." appears on the
screen.
•
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•
Only one receiver (home theater) can be connected.
•
Check if the Anynet+ device power cord b prepedy connected.
•
Check the Anynet+ device's Video/Audio/HDMI cable connections.
•
Check whether Anynet+ (HDMI-CEC) b set to On in the Anynet+ setup menu.
•
Check whether the TV remote control b in TV mode.
•
Check whether the remote control b Anynet+ compatible.
•
Anynet+ doesn't work in certain situations. (Searchingchannels, operating Media Play or Plug & Play (initial
setup), etc.)
•
When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
and on again.
•
Check if the Anynet+ Function of Anynet+ device is set on.
•
Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (H DMI-CEC) is set to
On in the Anynet+ Setup menu.
•
Press TOOLS button to display the Anynet+ menu and select a menu you waist.
•
Select View -IV in the Anynet+ menu.
•
Press the SOURCE button on the TV remote control and select a non- Anynet+ device.
•
Press v
CH A,
PREoCH, and FA_LCHto change the TV mode. (Note that the channel button operates
only when a tuner-embedded Anynet+ device is not connected.)
•
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
•
Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet+ device does not play.
•
You cannot use the play function when Plug & Play (initialsetup) is in progress.
The connected device is not
displayed.
The TV Program cannot be
•
recorded.
The TV sound is not output
•
Connect the optical cable between TV and the receiver.
through the receiver.
•
Check whether or not the device supports Anynet+ functions.
•
Check whether or not the HDMI cable is properly connected.
•
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
•
Search Anynet+ devices again.
•
You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support Anynet+
functions.
•
If connection is terminated because there has been a power interruption or the HDMI cable has beers
disconnected, please repeat the device scan.
Check whether the antenna jack on the recording device is properly connected.
0
English
Hide quick links:
Advertisement
Table of Contents
