Safety Strap; Before Turning On Tv; Check Accessories; Tv Stand Installation - RCA LED42C45RQ User Manual

as power-supply cord or p lug is damaged, liquid has been spilled
or o bjects have fallen into the a pparatus, the a ppratus has been
exposed to rain or m oisture, does not operate normally, or h as
been
dropped.
15. This TV should be operated only from the type of power supply
indicated on the rating label. If customer is not sure the type of
power supply in your home, consult your appliance dealer or local
power company. For 31/remote control battery power, refer to the
operating instructions.
16. The TV set shall not be exposed to dripping or splashing. No
objects filled with liquids, such as vases, shall be placed on the TV
set.
17. Never push objects of any kind into this TV through openings as
they may touch dangerous voltage or other electrical parts that
could result in fire or electric shock. Never spill liquid of any kind
into the 31/.
18. Unplug the TV from the wall outlet before cleaning. Do not use
liquid or aero cleaners. Use a damp cloth for cleaning.
19. This ql/should never be placed near or over a radiator or heat
resource. This TV should not be placed in a builtdn installation such
as a bookcase or rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
20. Do not place this TV on an unstable cart, stand, tripod, bracket, or
table. The TV may fall, causing serious injury to someone, and
serious damage
to the appliance.
21. Do not attempt to service this 31/by yourself because opening or
removing covers may expose you to dangerous high voltage or
other hazards. Refer all servicing to qualified service personnel.
22. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) tHs device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
23. WARNING: To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the installation
instructions.
24. To reduce the risk of electric shock, the grounding of center pin of
plug must be maintained.
25. If an outside antenna or cable system is connected to the TV, be
sure the antenna or cable system is grounded to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA NO.70,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrodes. (See figure A)
LEAD IN
WIRE
{_ROUND CLANIP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 8/0 2O)
GROUNDING CONDUCTORS
(NEC SECTION 810 2/)
ELE IP_ GROUNDING
E QU IP _,'IE N T ELECTRODE SYSTEM
(NEC ART 250 PARTH)
Figure A
Safety Strap
Caution: Pushing, pulling or climbing on the 31/may cause the 31/
fa,ing. Do not let chlidren climb or hang on the TV. Always place the TV
on a sturdy, level, stable surface that can hold the weight of 31/. And if
possible, secure the TV according to the instruction below (Note: The
fastening components such as screws are not supplied with TV).
Step one: Insert the M6 mounting screws into the upper b_vowall
mounting screw holes and fasten them (Figure B).
Step two: Insert anchors to wall and connect the bolts and anchors
with ropes or chains (Figure C).
Figure B Figure e
3
Before Turning On TV
Check Accessories
Check tile accessories that are packed with yeur 11/.
PART NO.: RE2OQPSO
(_ SCREWS
M4 x 1 2mm, 6pcs
Part# RS01TM41 2H
SCREWS
M4rl_ 14ST0'_1 ' 4pwPASl 4HT
E::
USER'S GUIDE QUICK START GUIDE PATENT CARD
Setup rv Table Stand
Please refer to TV Stand Installation guide in next page to carry out
stand installing.
Select rv Location
Select a flat, stable table to place your TV set. Please follow the Safety
Instructions when placing the TV.
Connection and Using
After placing your 31/properly, you can connect the 31/with power
supply and cable components. For further information, see page 4 to
page 5.
Note: Above accessories are subject to change without notice.
TV LED42C45RQ is packaged with the TV stand separated from the
cabinet. To setup the TV table stand, please carry out the installation
according to the instructions below.
Step One
Place the TV faced down on a soft cloth or cushion to prevent the LED
LCD panel from being damaged.
The LED LCD panel can be
scratched easily, so please:
1. Choose an absolutely flat
surface to place the TV on.
2. Use soft cloth or cushion to
face the TV panel.
Do not put 31/on the table
directly.
ys unplug the AC cord first
when installing/removing the stand.
Step Two
Take the neck. Please align the screw holes of the neck and the TV, and
then insert the 6 screws into the 6 holes on the neck and tighten them.