Service; Starting A Warm Engine; Starting A Flooded Engine; Clean Air Filter - Poulan Pro 25 HHT Instruction Manual

STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENGINE.
NOTE: Keep the throttle tock engaged until
the engine starts.
5. Pull starter rope sharpty until engine runs,
but no more than 5 pulls.
6. Allow the engine to run 10 seconds, then
move the choke tever to the OFF CHOKE
position.
7. Release the throttle lock by squeezing and
releasing the trigger.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not
run. it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
STARTING A FLOODED ENGINE
Flooded engines can be started by p_acing
the ON/OFF switch in the ON position and the
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then.
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn't start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
=1L
r=WARNING:
Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performh_g mah_tenance
except for carburetor adjustments.
HELPFUL TIP
IMPORTANT: Have aft
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
Service dealer performs work on the
product, Electrolux Home Products,
Inc.i may not pay for repairs under war-
ranty. Itis your reaponsibility to maintain
and perform general maintenance.
INSPECT AND CLEAN UNIT AND
LABELS
• Before and after each use. inspect com-
plete unit for loose or damaged parts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Air Filter
Cover
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive fult value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Plug Boot
• Air Filter
• Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
• ON/OFF Switch - Ensure ON/OFF switch
functions property by moving the switch tothe
OFF position. Make sure engine stops; then
restart engine and continue.
• Fuel Tank - Do not use unit if fuel tank shows
signs of damage or leaks.
• Gearbox - Do not use if the gearbox shows
signs of damage or leaks. After 50 hours of
use, we recommend that your gearbox be
serviced by an authorized service dealer.
Air Filter Screw %
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create afire
hazard or produce harmful evaporative emis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter; squeeze
filter to distribute oil.
6. Replace parts.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
WARNING:
The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
-6-