Applied Operations - Pioneer LaserDisc CLD-D504 Operating Instructions Manual

APPLIED OPERATIONS
0_= _
To play an LD from the position where
playback was last stopped
If • or POWER is pressed during playback, and playback has not
reached the middle of the disc, it is possible to restart playback
from the position where it was stopped.
When playback of an LD is stopped by pressing • or POWER, the
address where the playback is stopped is stored in memory and,
provided that the disc is left in the LD disc table, the stored ad-
dress is held in memory even after the power is switched off.
When you switch the power on and press LAST MEMORY, play-
back starts from the position where it was last stopped.
LAST
MEMORY
To start playback directly from the position where it was
stopped:
Position slightly before
Position where playback
was stopped
Press LAST MEMORY once. Playback starts from the position
slightly before the position where it was last stopped.
To start playback after reviewing the plot from the begining
to the position where it was last stopped:
Start /and
fast forward .,_| _-__1
/ are repeated' _ L_ 1
Press LAST MEMORY consecutively twice. A short period of play-
back and fast forward operations are repeated from the beginning
of the disc until slightly before the position where playback was
last stopped, and normal playback starts from there. By pressing
LAST MEMORY again during the fast forward operation, playback
can be started directly from slightly before the position where it
was last stopped.
NOTES :
• The last memory playback function is available only with
LDs. It is not available with CD and CDV discs.
• If playback was last stopped in the middle of side B of a
double-sided disc, the last-memory playback starts from side
B.
• When I_ is pressed to start playback after it has been stopped
with •, playback starts from the beginning of the disc.
• Be sure to leave the disc inside the player. The last-memory
playback is not possible once the disc has been taken out of
the player.
• Be sure to plug the AC power cord into a power outlet to
which power is supplied permanently.
I udio switching I
Every time AUDIO D/A is pressed during playback, the played
audio is switched. This makes it possible to;
• listen to the analog audio of a disc with digital audio;
• listen to only one of the two channels of a stereo disc;
• select the audio to be played from multiplexed audio disc.
LD with digital audio
It is possible to switch between the digital and analog audio and
between the L (Left) and R (Right) channels of stereo audio.
Digital audio Analog audio Analog audio
r - - 7
AUDIO (stereo) (stereo) L CH
÷E 5
I_ Digital audio __ Digital audio __ Analog audio__J
R CH L CH R CH
• In a case of a disc recorded with Dolby AC-3 signal, only
the left channel signal is heard in monaural mode when an
analog audio is selected.
LD with analog audio
• Disc containing CX auto ON (OFF) switching codes
_ r_AUDIO r Stereo audio _ L CH _0,- R CH
• Disc without CX auto ON (OFF) switching codes
CX OFF CX ON CX ON
AUDIO _ (stereo) "_'-_ (stereo) --" (L CH) 4.._ _
_ r_ CXOFF4__.__ CXOFF ____._ CXON
(RCH) (LCH) (RCH)
and
AUDIO
_ _ Stereo audio _ LCH _P- RCH --7
LD with E)._* mark
C)_ functions on the analog audio of LD.
With an LD carrying the C_,_4 m ark, audio can be played with re-
duced noise using the CX noise reduction system.
Some of the discs carrying the E)_ mark do not contain the codes
for automatic ON/OFF switching of the CX system. With such
discs, turn CX ON by pressing AUDIO D/A on the remote control
unit.
• IC_,_4 is a trademark of CBS. This player conforms to the extend-
ed specifications of CX. 1 5
<VRB 1147>