Operating Netcommand-Controlled Devices - Mitsubishi Electric DLP C9 Series Owner's Manual

48 5. NetCommand IR Control (837 Series)
Operating NetCommand-Controlled Devices
Controlling Most Device Types
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press CHANNEL UP. NetCommand
then sends the "learned" channel-up control signal to
the cable box.
1, Perform NetCommand setup for the device as
described in this chapter.
When you wish to use the device, press ACTIVITY.
3, Press A V 4 _ to highlight the icon for the device.
4, Press ENTER to switch the TV to the device.
Note:
G_
Z
if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automati-
cally switch to the correct input for the device.
To operate the device using the TV's remote
control, press the side button to put the remote
control into TV mode.
Point the remote control at the TV (not the device)
and press the key for the desired function.
Press the MOREkey to access additional key func-
tions you may have "learned" for the device.
Special Operation Methods
Manual Power On/Off
Use for devices that have only one POWER key.
1. Press ACTIVITY.
2. Press A V _ I_ to highlight the icon for the
device to be powered on or off.
3. With the Activity menu still displayed, press
POWER to send the power signal; you may
need to press POWER twice.
Note: If you press POWER without theActivity
menudisplayed, theTVwillturnoff.
4. PressENTERtoswitchtheTVtothedevice.
Automatic Power0n/0ff • ToPower0ntheDevice
This feature is only for devices that have separate 1. Press ACTIVITY.
POWER ONand POWER OFFkeys on their original 2. Press A Y 4 _ to highlight the icon for
remote controls. If your device does not have a the device to be powered on or off.
separate POWER OFFkey, do not use the Power
3. Press ENTER to switch the TV to the
Off learning position use only the Manual Power ............
....... aevlce anu i'Jetuommane will sene me
ul'J/uvv metnoa oescr oeo above _
_'ower un command to me aevlce.
In the NetCommand Learn screen:
...... • To Power Off the Device
a Learn the _'ower un commana n me , _, .. _,
...... vvnen you turn me iv oft the _v senas aH
................................... _'ower un earn ng post on
.... " learned Power Off commands to all devices.
b. Learn the Power Off command in the
PowerOfflearning position.
.......... command to the current device.
Learn tne M_'NUKey on tne or@nai remote in tne
en,u !earning P°S!ti°n_ ..................................... I ..................................................
11
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii: 1. "Learn'theGUIDEkeyontheoriginal remotein
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii theGuidelearningposition.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii: 2. LearnthePAGEUPand PAGEDOWN keysofthe
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii: original remote in the Page Up and Page
__ Downlearning positions.
display the guide.
2. Press PAGE UP/DOWN (,_ _v) to send the Page
Up/Dn commands for the guide.