KitchenAid KSC24C8EYW00 User Instructions page 4

The refrigerator and freezer controls arelocated o nthedispenser
panel.
IMPORTANT: The display s creen o nthedispenser control panel
will t urn offautomatically andenter " sleep" mode when the
control buttons a nd dispenser levers h ave notbeen used for
2minutes ormore. While in"sleep" mode, thefirstpress o fa
control button will o nly reactivate thedisplay s creen, without
changing any settings. After r eactivation, changes toany settings
canthen bemade. Ifnochanges aremade w ithin 2 minutes, the
display willre-enter "sleep" mode.
• Touch a ny control button onthedispenser panel toactivate
thedisplay s creen. The home screen w illappear asshown.
Adjusting the Controls
For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator, make
sure that the controls are still set to the "mid-settings." The factory
recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IM PO RTANT:
• Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a colder than
recommended setting will not cool the compartments any
faster.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To view and adjust the set points, press and hold the
TEMPERATURE button for 3 seconds. When adjust mode is
activated, adjusting information will appear on the display screen.
NOTE: To view Celsius temperatures, press the LIGHT button
when adjust mode is activated. To return the display setting to
Fahrenheit, press LIGHT again.
When adjust mode is activated, the display screen shows the
refrigerator set point and "REFRIGERATOR" appears.
Press LOCK to raise the set point, or press OPTIONS to lower
the set point.
When you have finished viewing (and adjusting if desired) the
refrigerator set point, press TEMPERATURE to change the
display to show the freezer set point. When the zone has been
changed, "FREEZER" appears on the display screen.
Press LOCK to raise the set point, or press OPTIONS to lower
the set point.
When you have finished viewing (and adjusting if desired) both
the refrigerator and freezer set points, press MEASURED FILL
to save the settings.
NOTE: To exit without saving changes, press ICE MODE at
any time while in adjust mode, or allow about 60 seconds of
inactivity and adjust mode will turn off automatically.
When adjusting temperature set points, use the following chart as
a guide.
CONDITION: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Setting
1o higher
REFRIGERATOR too warm REFRIGERATOR Setting
1o lower
FREEZER too cold FREEZER Setting
1o higher
FREEZER too warm / FREEZER Setting
Too little ice 1o lower
The set point range for the refrigerator is 33°F to 45°F (0°C to
7°C). The set point range for the freezer is -5°F to 5°F (-21 °C to
-15°C).
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off.
• To turn cooling off, press and hold the LOCK and MEASURED
FILL buttons at the same time for 3 seconds.
IMPORTANT: To avoid unintentionally mockingthe dispenser
or changing other settings, be sure to press both buttons at
exactly the same time.
When cooling is off, "REFRIGERATION COOLING IS OFF" will
appear on the display screen.
Press and hold LOCK and MEASURED FILL for 3 seconds
again to turn cooling back on.
Additional Features
Max Cool and Max Ice
The Max Cool feature assists with periods of heavy ice usage, full
grocery loads, or temporarily warm room temperatures.
The Max Ice feature assists with temporary periods of heavy ice
use by increasing ice production over a 24-hour period.
• To turn on the Max Cool feature, press the OPTIONS button to
enter Options mode, then press OPTIONS again to activate
the feature. The Max Cool icon will appear on the dispenser
display.
G
The Max Cool feature will remain on for 24 hours unless
manually turned off. To manually turn it off, press the
OPTIONS button to enter Options mode (unless you are
already in Options mode), then press OPTIONS again. When
the feature has been turned off, the Max Cool icon will
disappear on the dispenser display.