Advertisement
READ AND SAVE THESE
Please read the instructions in this booklet and in
the installation instructions before you install and
use your range heed= By doing so you will be sure
of obtaining the full benefits of the quality and con-
venience built into your range hood. It will also avoid
needtess service expense resulting from causes
beyond our control which cannot be covered In our
warranty
Failure to fo]Iew these instructions could invalidate
the warranty, cause a malfunction, and result in
death, serious
bodily
injury,
andtor property
damage,
1
ALL ELECTRICAL WORK MUST BE DONE IN
ACCORDANCE
WITH LOCAL ANDfOR NA-
TIONAL ELECTRICAL CODE AS APPLICABLE.
INSTRUCT ONS
FOR SAFETY,
THIS PRODUCT
MUST BE
GROUNDED. IF YOU ARE UNFAMILIAR WITH
M_--rHODS OF INSTALLING
ELECTRICAL
WIRING,
SECURE
THE SERVICES
OF A
QUALIFIED ELECTRICIAN.
2
TURN OFF POWER AT SERVICE ENTRANCE
BEFORE INSTALLING, WIRING OR SERVIC-
iNG THIS PRODUCT.
3
Use only motet duct. DO NOT USE PLASTIC
DUCTI Tape all duct connections
4
CAUTION: (Ducted Fans Only) Always vent
this product to the outside - NOT into spaces
within walls or ceilings, attics, crawl spaces,
garages, etc.
5. To avoid motor bearing damage
and notsy
andlor unbalanced impellers,
keep drywalI
spray, construction dusL etc off power u=lit
6, For bast capture of cooking impurities, your
range hood should be mounted 18_24" above
the cooking surface.
7
Fireplaces, gas furnaces, water heaters and the
like, require proper flew of combustion air and
exhaust. To prevent this flow from being altered
by an exhaust fan, follow the heating equipment
manufacturer's guidelines and see safety stan-
dards such as those published by NFPA and
ASHRAE
8
Please read specification {abel on product for
further information and requirements
HOW TO AVOID A COMMON RANGE-TOP GREASE FIRE
= Your range hood provides a protective barrier between the cooking surface and the cabinets
o Keep fan, filters and grease laden surfaces CLEAN according to instructions.
* Always turn hood ON when cooking at high heat to keep the cooking area clean and the hood cooler
* Use high heat settings only when necessary,
,, Never leave cooking surface unattended
Boil-over causes smoking and greasy spillovers that may ignite
o Always use adequate-sized utensils.
,, If preparing
flaming foods, such as Cherries Jubilee, always turn hood ON to HIGH to prevent a high heat situation which can cause damage or fire
HOW TO EXTINGUISH A COMMON RANGE-TOP GREASE FIRE
. Never pick up a flaming pan tf dropped, flames can spread quickly.
a DO NOT USE WATERt A violent steam explosion may result Wet dishcloths or towels are also dangerous.
= Smother flames wttha close fitting lid, cookie sheet or metal tray
° Flaming grease can also be extinguished with baking soda or a multi-purpose dry chemical extinguisher
. ]'urn off surface units - ff you can do so without getting burned_
OPERATING
The 510 series hood may be installed as either
a vented or ventless hood using the kits listed
below
Purchase
these kits at any Sears store
INSTALLING
A VENTED
HOOD
!
Purchase
a 59101
Vented
Kit,
which
contains:
1 - Black plastic vent cover
1 - Damperlduct
connector (fits 3-!14" x 10"
duct)
2
Snap the black vent cover over the vents in
the hood front
3
instant the damperlduct
connector
INSTALLING
A VENTLESS
HOOD
1. Purchase a 50183 Ventless Kit, which con-
tains one Clean Cooking System I fllter
Filter Replacement
Filters on the 5t0 series hood are removed by
turning the filter retaining
clip to the side and
lifting the filter out In the vented version, turn
the filter retaining
clip to one side and place the
aluminum
filter under the embossed
retaining
tabs on the back of the fan housing
Turn the
retaining clip so that the low end of the clip holds
the filter in place.
In the ventless version,
place the Clean Cook-
ing System I filter under the aluminum filter with
the blue side next to the fan blade. Place the
filters under the retaining
tabs on the back of
the fan housing and turn the filter retainer clip
so that the high end of the clip holds both filters
in place MAKE SURE THAT THE BLUE SIDE
OF THE CLEAN COOKING SYSTEM FILTER IS
NEXT TO THE FAN BLADE WHEN THE FILTER
IS INSTALLED.
NOTE;
Make sure that the arrows on the filter
retaining clip point toward the front and back of
the hood
The aluminum filter on the 5t6 series is remov*
ed by turning the retaining clip toward the back
of the hood. When replacing
the filter, hook the
filter into the two retaining tabs on the right side
of the hood and turn the retaining tab to secure
the left side. BE SURE TO POSITION
WIRES
FROM
MOTOR
IN RECESS ON FILTER
SO
THAT
WIRES
ARE
NOT PINCHED
UNDER
FILTER
iNSTRUCTiONS
Switches
The fan and light are each controlled by e rocker
switch. The light switch has two positions, "ON"
and "OFF".
The fan switch has three positions
- "HIGH",
"LOW",
and "OFF"
("OFF"
is the
middle position .)
Cleaning
Always disconnect the electricity from the range
hood before servicing_ Keep your range hood
clean by using a mild detergent
suitabJe for
painted surfaces. DO NOT USE ABRASIVE
CLOTH, STEEL WOOL PADS OR SCOURING
POWDERS, The fan assembly is designed to be
easily removed for cleaning, See "Fan Assembly
Removal"
below.
Aluminum filters are dishwasher
safe Avoid ex-
tremely caustic cleaning agents, however. They
may discolor the aluminum.
Clean filters once
a month
Do not wash the Clean Cooking System I filter
used in ventless hoods
Washing
the filter will
destroy
its effectiveness.
The Clean Cooking
System I filler will last up to twelve months with
normal use. Replace the filter whenever the blue
side becomes
noticeably
dirty or discolored
Light Bulb Replacement
The light buEb (not supplied with hood) should
be 75 Watt maximum
Remove the light _ens
covering the bulb by pressing the two extending
tabs together until they release from the retain-
ing slots in the hood.
FILTER
RETAINING
ALUMINUM
SERIES
FILTER
5t6
To Remove Fan Assembly
Make sure that power is disconnecLed
Remove
filter. Remove two screws holding motor bracket
to range hood Unplug fan assembly Be careful
not to allow fan assembly
to drop when screws
are removed
Be careful not to bend or damage
the fins on the blade -- they will be put out of
balance
COVER
PLATE
SERIES
510
WIRING
DIAGRAM
B_
_-L_
I
L_LIh t
I
8__
t _
MOtOr
I
Swi¢¢h
I
_
"
0''
5wltcll
|T,, f
I
i-
)L=_'_t3
I
I
H
Rnr_
Hoo_
J_nctto_
Box
Note
- If
_ny
of
the
original
wire
on
the
hood
h_l
to
bo
repla¢od,
it
=hould
be
top|aced
by
wiring
h_lvl_g
equ[vl_i_nt
{nlutmtion
and
tempar_lure
rating
(lOS
C Tho;'mopialltl¢
AWt'_
U,L
Lh_tod)
Advertisement
