Table of Contents
Advertisement
Cycle Options
+ add
steam
+ warn'
+ [Red_um
energy
saver
+ CO[O
_ tow
_Ig
[
+ freshwater
dnse
+ CO[_ water
+ no SD] _
+extra
c_ean
light
:teaB
auto
Sp_n
SO_[
+ _asher
_a.ce[ temp
speed
revel
START
co+_tmt
Pause
+ {oc+<
To add options, p ressthecorresponding options buttons
to illuminate the selections desired. T o delete options,
presstheoptions buttons againand the indicator lights
will turn off. Some Options require a "Press & Hold" effort
to activate or deactivate the secondary function.
Not all options are available on every model. To protect
your fabrics, not all options are available with every cycle.
If an option is not appropriate for the cycle, the indicator
will not light. Occasionally, a setting and option in the same
cycle will conflict with each other, like Add Steam and
Energy Saver. When this happens, the option selected
first will cause the conflicting option to not be selectable.
To change Options
after the cycle starts, press Pause,
adjust the setting and press Start to resume the cycle.
Energy Saver
The Energy Saver option reduces the warm water
temperature a few degrees to save energy and also
extracts more water to reduce drying time. On some
models, you may also notice after the cycle begins most
lights and indicators will turn off. To turn those lights
temporarily back on press Energy Saver during the cycle.
Add Steam
Select this option to add approximately 20 minutes
of tumbling in steam during the wash cycle. It is
recommended for heavily soiled loads to help enhance
the release of tough stains from fabrics after initial
agitation. It is available with all cycles except Delicates,
Quick Wash, Rinse & Spin and Spin Only.
Steam may not necessarily be visible inside drum
during a steam wash cycle.
- Steam may not be present during entire steam wash
• Ifsteam is selected, rinse temperatures will be elevated.
If washer is paused during a steam wash cycle, the
door will remain locked due to higher temperature
in drum. DO NOT force open - it will unlock upon
cooling.
- During a steam cycle you may notice steam exiting
from the rear vent of the washer =this is normal and
not cause for alarm.
Pre Wash
Select this option to add a short initial wash period to
a cycle. Heavily soiled and stained loads will prewash
for approximately 5 minutes. The water will drain and
the load will automatically advance to the regular wash
cycle.
See step 5 in "Operating Your Washer" section in this
guide for details on adding detergent to the dispenser.
Chime (Press & Hold)
A signal will sound at the end of the cycle if this option
is selected.
Delay Start
Press Delay Start to select a wash time convenient
to your schedule or during off peak energy hours.
The delay time selected will be displayed and begin
counting down when you select Start.
Max Fill (Press & Hold)
Increase the water fill level of the agitation portion of
any wash cycle.
Freshwater
Rinse
Use this option when additional rinsing is desired to
remove excess dirt and detergent. It is recommended
for heavily soiled loads or if household members have
sensitive skin.
Clean Washer
To clean and freshen the washer, perform the Clean
Washer
cycle. Ifyou wish to begin the cycle, press
select when prompted. This maintenance cycle uses hot
water and two rinses to remove residue that may cause
odor. See "Inside Routine Cleaning (Preventative)"
for
detailed information
about the Clean Washer cycle.
The washer will automatically prompt you to run the Clean
Washer cycle every 50 cycles. You may press the Cancel
button to manually perform the cycle at another time.
Control Lock
To lock the controls between cycles, press and hold the
Control
Lock button for 5 seconds. Repeat to unlock
the controls when you are ready to operate the washer.
Use this feature to reduce the likelihood of accidental
operation by children.
Advertisement
Table of Contents
