Table of Contents
Advertisement
Electrical
Information
These
guidelines
must be followed
to ensure
that safety
mechanisms
in the design
of this appliance
will operate
properly.
Avoid fire hazard or
electric shock. Do not use an extension cord
or an adapter
plug.
Do not remove
any
prong from the power cord.
Grounding type
walmreceptacle
Power suppmy
cord with 3-prong
grounding pmug
•
Refer
to the serial
plate
for
correct
electrical
rating.
The
power
cord
of the appliance
is equipped
with
a three-prong
grounding
plug for protection
against
shock
hazards.
It must
be plugged
directly
into its own properly
grounded
three-prong
receptacle,
protected
with a 15 amp time delay fuse or circuit
breaker.
The receptacle
must
be installed
in accordance
with
the local codes and ordinances.
Consult
a qualified
electrician.
Receptacles
with Ground
Fault Circuit
Interrupters
(GFCI)
are
NOT
RECOMMENDED.
DO
NOT
USE
AN
EXTENSION
CORD
OR AN ADAPTER
PLUG.
•
If the
voltage
varies
by
10 percent
or more,
appliance
performance
may
be affected.
Operating
the appliance
with
insufficient
power
can damage
the motor.
Such
damage
is
not covered
under the warranty.
If you suspect
your voltage
is
high or low, consult
your
power
company
for testing.
•
To prevent
the appliance
from
being
turned
off accidentally,
do not plug the unit into an outlet
controlled
by a wall switch
or pull cord.
•
DO NOT pinch,
knot,
or bend the power
cord
in any manner.
Other
Precautions
•
NEVER
unplug
the appliance
by pulling
on the power
cord.
Always
grip
the
plug
firmly
and
pull straight
out from
the
receptacle.
•
To avoid
electrical
shock,
unplug
the
appliance
before
cleaning.
NOTE:
Turning
the control
to "OFF"
turns
off the compressor
but does
not disconnect
power
to other
electrical
components.
Installation
and Setup
Inspection for Damage
inspect
the underside
of the cabinet
and packaging
for damage
such as a fork truck
can cause.
If hidden
damage
is found
after
uncrating,
immediately
call the delivery
carrier
and request
an
inspection.
Retain
all packaging
and crating
materials
until the
inspection
is complete.
Uncrating
and Set-up
• Using
a utility
knife
with a sharp,
short
blade,
cut along
the
perimeter
of the carton
as indicated.
• Lift the carton
off the product.
• Remove
the package
containing
the casters
from the unit. This
package
will contain
the following
items:
•
One (1) wrench
•
Sixteen
(16) screws
•
Four (4) casters
Casters
With an assistant,
tilt the unit until it is resting
on its back. Take
care
to protect
the
back
from
being
scratched
during
this
process.
Using the wrench
provided
and the sixteen
(16) screws,
install
all four
(4) casters
in the tapped
holes
in the bottom
of the
unit. Tighten
the screws
securely.
With an assistant,
tilt the unit back up onto
its casters.
To prevent
unintended
movement,
block casters
once the unit
is in place.
Appliance
Placement
Leave
a three
(3) inch
space
on all sides
and the back of the
cabinet
for adequate
air circulation.
Choose
a place that is near
a grounded
electrical
outlet.
For the most
efficient
operation,
the appliance
should
be located
where surrounding
temperatures
will
not
drop
below
40°F
(43°C)
or exceed
110°F
(43°C).
Additional
compressor
heaters
are not recommended.
Insulation
The insulated
space
on this cabinet
is sealed
to maintain
peak
efficiency.
DO NOT drill holes in the cabinet.
Holes
drilled
in the
cabinet
may
destroy
that seal
and damage
electrical
wiring
located
in the insulated
space.
It may also pierce
and damage
the sealed
refrigeration
system
in the insulated
space.
DAMAGED
ELECTRICAL
WIRING
OR WET INSULATION
CAUSED BY DRILLING WILL VOID THE WARRANTY.
Hide quick links:
Advertisement
Table of Contents
