Jenn-Air JFC2089WEM1 User Instructions page 12

For your convenience, your temperature controls are preset at the
factory. When you first install your refrigerator, make sure the
controls are still set to the recommended set points as shown.
Recommended Settings
0 : {3 d _'_ }): }
::/i(}i_ } 4 ::</Oi}S
IMPORTANT: When the power is on, the temperature display
shows the set point temperature of the compartment.
To Turn Your Refrigerator Off/On:
• Press the freezer (+) control repeatedly until "OFF" appears in
the freezer display. Allow a few seconds for the refrigerator to
shut off. Neither compartment will cool.
• Press either the refrigerator or freezer (+) or (-) touch pads to
turn on the refrigerator.
Adjusting Digital Controls
The REFRIGERATOR control adjusts the refrigerator compartment
temperature. The FREEZER control adjusts the freezer
compartment temperature.
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the chart as a
guide.
To Adjust Set Point Temperatures:
The first touch of either the (+) or (-) touch pad displays the current
temperature set point.
• Press the (+) or (-) control until the desired temperature set
point is displayed.
NOTE: Except when first turning on the refrigerator, do not
adjust either temperature control more than one setting at a
time. Wait 24 hours between adjustments for the temperature
to stabilize.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm Adjust REFRIGERATOR
Control 1° lower
FREEZER too warm/too little ice Adjust FREEZER
Control 1° lower
REFRIGERATOR too cold Adjust REFRIGERATOR
Control 1° higher
FREEZER too cold Adjust FREEZER
Control 1° higher
Additional Digital Control Center Features
Max Cold
The max cold feature assists with periods of high refrigerator use,
full grocery loads, or temporarily warm room temperatures.
• Press the MAX COLD touch pad to set the freezer and
refrigerator to the lowest temperature settings. Press the MAX
COLD touch pad again to return to the normal refrigerator set
point.
NOTE: The Max cold feature will automatically shut off in
approximately 12 hours.
Speed Ice Feature
The Speed Ice feature assists with temporary periods of heavy ice
use by increasing ice production.
• Press the SPEED ICE feature touch pad to set the freezer to
the lowest temperature setting. Press the SPEED ICE feature
touch pad again to return to the normal freezer set point.
NOTE: When Speed Ice is on, neither the (+) or (-) control for
the freezer will operate. The Speed Ice feature will
automatically shut off in approximately 24 hours.
Humidity Control (on some models)
The Humidity Control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Humidity Control is on.
• Press HUMIDITY CONTROL when the environment is warm
and more humid, or if you notice moisture on the door hinge
seal. The indicator light will be lit when humidity control is ON.
• Press HUMIDITY CONTROL again to turn OFF and save
energy when the environment is less humid.
- dy
Vacation Mode (on some models)
In Vacation Mode, the freezer will not automatically defrost as
often to conserve energy.
• Press the Vacation Mode touch pad until the indicator light is
lit to turn on this feature. Press the Vacation Mode touch pad
again or open the refrigerator door to turn off this feature.
NOTE: The refrigerator door may be opened within 1 hour of
setting Vacation Mode without turning off the feature.
Vacas or!
Temp Alarm
The Temp Alarm feature provides temperature information in the
event of a power outage.
Power outage: During a power outage, if the temperatures in the
refrigerator and freezer compartments exceed normal operating
temperatures, the highest temperature reached will be displayed.
• Press the TEMP ALARM touch pad until the indicator light is
lit, to turn on this feature. Press and hold TEMP ALARM for
3 seconds until the indicator light goes off to turn off this
feature.
Temperature alarm: An alarm will sound repeatedly if the freezer
or refrigerator compartment temperatures exceed normal
operating temperatures for an hour or more.
The temperature displays will alternately show the current
temperatures and the highest temperatures the compartments
reached.
Press the TEMP ALARM touch pad once to stop the audible
alarm and alternating temperature displays. The Temp Alarm
light will continue to flash until the refrigerator returns to the
set temperature.
12