Burner Flame Check; Electronic Ignition - Kenmore 415.23667310 Use & Care Manual

ignitor Lighting (continued)
8. Once each burner has ignited, turn knobs to desired setting.
9. If ignitor does not work, follow match lighting instructions.
Turn controls and gas source or tank OFF when not
in USe.
CAUTioN
Burner Flame Check
" Remove cooking grates and Heat Diffusers. Light burners, rotate
knobs from Hi to LOW. You should see a smaller flame in
LOW position than seen on Hi. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
If ignition does NOT occur in 5 seconds, turn the burner
controls OFF, wait 5 minutes and repeat the lighting
)rocedure. if the burner does not ignite with the valve
open, gas will continue to flow out of the burner and
could accidentally ignite with risk of injury.
Match-Lighting
Do not lean over grill while lighting.
1. Open lid. Turn ON gas at LP cylinder.
2. Place match into match holder (hanging from side panel of
grill). Light match; then light burner by placing match through
the match light hole on right or left side of grill.
3. Push in and turn far right or far left burner knob to the HI
position, depending on match light hole selected. Be sure
burner lights and stays lit.
4. Light adjacent burners in sequence by pushing knobs in and
turning to the Hi position.
Sideburner ignitor Lighting
Do not lean over grill while lighting.
i. Open sldeburner lid. Turn ON gas at LP cylinder.
2. Turn sideburner knob to the HI position, push and hold
ELECTRONIC IGNITION button.
3. If sideburner does NOT light within 5 seconds, turn knob to
OFF, wait 5 minutes, then
repeat lighting procedure.
Sideburner Match Lighting
1. Open sldeburner lid. Turn ON
gas at LP cylinder.
2. Remove steamer tray and basket.
3. Place lit match near burner.
4. Turn sideburner knob to the
Hi position.
Be sure burner lights and stays lit.
5. Replace steamer tray and basket.
12 • 464323113
Turning Grill Off
- Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.
Ignitor Check
" Turn gas off at LP cylinder. Press and hold electronic ignitor
button. A "Clicking" should be heard and spark seen each
time between each collector box or burner and electrode.
See "Troubleshooting" if no click or spark.
Valve Check
* Important: Make sure gas is off at LP cyffnder before
checking valves. Knobs loci< in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
- Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
identical replacement part valve/hose/regulator as
specified in the Parts List of this Use and Care Guide.
General Grill Cleaning
- Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grffl/oven cleaner to painted
surfaces.
" Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
" Porcelaln surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
" Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
" Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
" Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.