Advertisement
f
Transmitter
Complance
Statement
Transmitters comply with al United States and Canadian legal requirements as of the date
of manufacture, No warranty is made that they comply with al UegaU r equirements of any
other jurisd'iclon. If transmitters are to be used in another country, the importer must
determine compUiancew4h any UocaUUaws and reguUatlonswhich may differ from United
States and Canadian requirements prior to use.
Los transmisores cumplen con todas Uas regUamentadones UegaUes de los Estados Unidos
y deUCanad_,en Ua fecha de fabricaci6n, Ninguna garantfa se da que cumplan con todas
as regamentaciones legales de ninguna otrajudsdicci6n.
Si los transmisores se van a
utlizar err otto pais,el importador debe determinar si cumplen con las reglamentaciones
y leyes locales que puedao ser diferentes alas reglamentadones de los Estados Unidos y
del Canada, antes de usar los mismos.
Les emetteurs sont conformes £ la r_gementation am@icaine et canadienne _ compter
de leur date de fabrication, Aucune garantie n'est stipul@ indiquant qu'Is sont conformes
toutes les prescriptions juridiques d'autres autorit_s, Si les _metteurs sont utlis_s dans
d'autres pays, t incombe a I'importateur d'en d_terminer leur conformit_ aux lois et r_ges
locales pouvant diff@er de celes des Ctats-Unis et du Canada avant toute utlisation
desdits 6metteurs.
Sendeger£te entsprechen alen gesetzlchen Bestimmungen in den USA und Kanada zum
Zeitpunkt der Herstelung.Wir Obernehmen keine Gew£hr[eistung fijr die Einha[tung a[[er
gesetzlichen Bestimmungen in anderen Landem,Solen Sendeger£te in anderen L£ndern
eingesetzt werden, so muss der Importeur vor dem Gebrauch sicherstelen,dass die
Sendeger£te auch sokhen Iokalen Bestimmungen entsprechen, wekhe yon den
Bestimmungen der USA und Kanadasabweichen.
£,x,l)l {_II!II __iiI I £ I?._ £ I I I _I InI _k I_
4-1 __lSi _t£1t,_l_111°
;017l?,_!20_1-_t-_)'#,_lo)[_1c@.]1t¢'o5)tI,
BI tl&l_', ( 0 {_/IJ/E Y_ ,'L0 i)] _gR $]]Z) _
niEi_O] _ ]E_ Eke-XJ_qlA_ A_
U@ #q_xb_bA_o£8_slql _Ai ujq3_ _tL_E}£_£! £
SETTING CONTACT
REVERSE FUNCTION
Limit Switch and Force Adjustments must be completed
before checking the contact reverse function (Figure _A-3).
A
Open garage door using
Wall Console,
Figure _A-3
B
Lay a 2" x 4" board fiat in center
of doorway.
C
Close door using Wail Console.
Check that door stops and reverses
within
2 seconds after it
contacts
board:
,
if door does not reverse, decrease
Close Force until door reverses.
,
If door still does not reverse,
move Limit Switch toward door.
E
Check Safe-T-Beam ° System
operation:
,
If beam is blocked, door will
not close.
2" x 4" boa rd
hid fiat
ACCESSORIES
PROGRAMMING THE
REMOTE CONTROLS
,
Each Remote Control must be programmed
separately.
°
The Remote Controls will not cause the door
Opener to close the garage door if the Safe-T-
Beam® System is malfunctioning.
°
When programminc) the Remote Controls, they
must be at least 24 from the Antenna Wire.
Ifthe red Learn Indicator Light blinks
approximately 4 times per second,
lrogramming
has stopped.
If programming
as stopped, repeat the above steps.
Each Button on a 2 or 3 Button Remote Control
is for a different Opener. You cannot use more
than one Button per Remote, per Opener.
°
A maximum of seven Remote Controls or
Wireless Keypads can be stored into the
Receiver at one time. If a Remote Control
becomes lost, or if you want to delete a Remote
Control or Wireless Keypad, see To EraseAll
Receiver Memory."
A
To program one Button of a Remote Control (Figure MA-4):
Locate Learn Button and Learn Indicator
Light
on left side of Power Head (Figure _A-5),
Press and release Learn Button,
Red Learn
Indicator Light will blink 2 times per second,
Press Remote Control Button once within
30
seconds, Red Learn Indicator
Light will stay lit,
Press Remote Control Button again, Red Learn
Indicator Light will go out, indicating
that
memory is stored,
Press Remote Control Button again and the door
will operate,
B
Program each additional Remote using step A above
(up to seven),
To Erase AiJ Remotes
from
Power Head Memory
A
Press and hold Learn Button on Power Head for 10
seconds or untl Learn Indicator Light goes out.
Memory is erased:
Program Transmitter/Receiver
again as needed.
To Replace
Remote
Control
Battery
A
FOR NON-FLASHLIGHTMODELS
Pop offthe
back of the transmitter,
-
Use coin, pen, screwdriver or any similar device,
-
Replace old Battery with new coin type battery,
Replace back of remote,
B
FOR FLASHLIGHT MODELS
Slide open battery cover,
-
Replace old Battery with new AAA battery,
Replace battery cover,
8
For Help, call 1-800-35-GENl£
or vBit wwwogeniecompanyocom
Hide quick links:
Advertisement
