Advertisement
Quick Links
Operator's Manual
Triple Bagger Kit
Models 190-190-100 & 190-192-190
IMPORTANT: Read safety rules and instructions carefully
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered,
brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply
on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
FORM NO. 769-01136D.fm
PRINTED IN U.S.A.
3/13/07
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MTD 190-190-100
Summary of Contents for MTD 190-190-100
- Page 1 A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 FORM NO. 769-01136D.fm PRINTED IN U.S.A.
- Page 2 From the operator’s position, locate the model plate in the front, left portion of the plastic grass catcher cover. This information will be necessary to use the manufacturer’s web site and/or seek help from Customer Support Department or service dealer. MTD LLC P. O. BOX 361131 CLEVELAND,OH 44136 330-220-4683 www.mtdproducts.com...
- Page 3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
- Page 4 26. Use only accessories and attachments approved for this Do not tow heavy pull behind attachments (e.g. loaded machine by the machine manufacturer. Read, dump cart, lawn roller, etc.) on slopes greater than 5 understand and follow all instructions provided with the degrees.
- Page 5 Use only an approved gasoline container. Periodically check to make sure the blades come to Never fill containers inside a vehicle or on a truck complete stop within approximately (5) five seconds after or trailer bed with a plastic liner. Always place operating the blade disengagement control.
- Page 6 SECTION 2: LOOSE PARTS The grass catcher kit is shipped with following loose parts in the carton. Please remove all loose parts, including the hardware pack, from the carton before discarding it. Compare with Figure 1 to check that all parts were included. Note that the kit and the hardware pack contain extra items which are not used on your unit.
- Page 7 SECTION 3: ASSEMBLY & OPERATION NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake.
- Page 8 Attaching Blades • Remount the cutting deck following instructions in the owner’s manual of the tractor. WARNING: Always protect your hands while Install Deck Baffle servicing blades by wearing heavy work gloves or using heavy rags. • Remove two of the self-tapping deck screws on the front right side of your deck.
- Page 9 Attaching Discharge Chute Place short • Raise the deck to its highest position. strap here Place long • Raise the chute deflector on the deck and hold it strap here while you position the discharge chute over the chute opening. •...
- Page 10 SECTION 1: PARTS LIST FOR MODELS 190-190-100 & 190-192-190 17 11 16 24 See parts 23 2 27 13 break-down below Bagging Blades (Round Hole) *Included with Cub Cadet Models only! Components of Cover Assembly PN # 664-04018: Components of Bag Assembly:...
- Page 11 Model 190-190-100 & 190-192-190 Ref. Part No. Description 17200A Catcher Support Bracket 17247 Tubing Adapter 631-0221A Chute Elbow 664-04018 Cover Assembly (includes ref. 35 to 46) 683-0617 Bracket Assembly: Chute Stop 689-00002 Grass catcher Support Assembly 710-0597 Hex Bolt 1/4-20 x 1.0 710-0751 Hex Bolt 1/4-20 x 0.620 710-3008...
- Page 12 MTD LLC., P.O. Box 361131, Cleveland, OH 44136-0019...
Need help?
Do you have a question about the 190-190-100 and is the answer not in the manual?
Questions and answers