Troubleshooting Guide - Euro-Pro Shark Retractor EP187 Owner's Manual

FAMILIARISEZ-VOUS AVEC VOTRE RETRACTEUR
SHARK
1. Bouton de relâche
de la coupelle
2. Bouton de mise en marche
3. Coupelle à poussière (réservoir)
4. Trappe de succion
5. Bouton Rétracteur
6. Poignée
7. Suceur plat
Spécifications techniques
Tension : 120 V, 60 Hz
Intensité : 7.1 A
Avertissement : Les illustrations peuvent différer du produit lui-même.
8. Brosse à épousseter
9. Électrobrosse pneumatique
10. Boyau souple
11. Bandoulière
12. Écran à débris
13. Filtre HEPA
14. Sac de rangement
(non illustré)
16
OPERATING INSTRUCTIONS
Motor Thermostat
Important: This unit is equipped with
a motor protective thermostat. If for
some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE REASON
1. Power cord not firmly
HAND VACUUM plugged into outlet.
2. No power in wall outlet.
WILL NOT
OPERATE 3. Needs servicing.
4. Thermostat has tripped.
1. Dust cup is full.
HAND VACUUM 2. Unit clogged.
WILL NOT PICK-UP 3. HEPA dust cup filter
OR SUCTION needs cleaning or
POWER IS WEAK replacing.
4. Hose clogged
1. Rotating brush or elbow
TURBO BRUSH
obstructed.
DOES NOT
2. Belt broken.
ROTATE OR
3. Hose obstructed.
ROTATES
4. HEPA dust cup filter
SLOWLY
clogged.
1. Dust cup is full.
DUST ESCAPING 2. HEPA Dust Cup Filter is
FROM HAND not installed correctly.
VACUUM 3. There is a puncture/hole
in HEPA Dust Cup Filter.
HAND VACUUM
HOSE OR 1. Hose clogged.
BRUSHES WILL 2. Dust cup is full.
NOT PICK-UP
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call 1 (800) 798-7398.
4. Turn the unit off and unplug
from outlet. Allow unit to cool
down, then restart
1. Empty dust cup
2. Turn unit off and unplug from
wall outlet. Remove HEPA dust
cup filter and check for object(s)
in air duct and remove.
3. Clean or replace HEPA dust cup
filter.
4. Turn unit off and unplug from
wall outlet. Check for objects in
hose
1. Clear obstructions.
2. Call 1 (800) 798-7398.
3. Clear obstruction.
4. Clean HEPA dust cup filter.
1. Empty dust cup.
2. Review HEPA Dust Cup Filter
instructions.
3. Replace HEPA dust cup filter.
1. Remove hose and/or bushes.
Remove obstruction from hose.
2. Empty and clean dust cup.
5