Advertisement
OCCURRENCE
POSSIBLE
CAUSE/SOLUTION
ESEC displays " - - " message.
The ESEC Control will display " - - " in the digital display windows indicating that the ESEC
has a 'Lockout"
condition. This condition is normal when using the oven lockout or self-
clean features. Wait for the Self-Clean
cycle to completely finish or if using the Oven
Lockout feature, press the Lock control pad to unlock the oven door.
Oven electronic
control
beeps and
displays
"Ff, F2, F3, or F9."
ESEC displays "Er" message.
This oven is equipped with a state of the art electronic oven controller. Among the many
features is a full time oven circuit diagnostics system. The controller constantly monitors the
internal circuitry as well as several crucial oven circuits to insure they are all operating
correctly. If at any time one of these systems fails, the controller will immediately stop the
current operation and beep continuously
(flashing an error code of "F1, F2, F3, or F9" in the
controller display window.
ESEC displays
"F5,
F6 or F7"
message=
Oven control
beeps when you try
to enter times or temperatures
Poor baking
results.
Electronic control has detected a fault condition. Press CLEAR/OFF
to clear the display and
stop the beeping. Reprogram oven. If fault remains, record fault number. Press CLEAR/OFF
and contact a Servicer.
ESEC control has detected a fault condition. Turn all surface control knobs to OFF and reset
the clock with the correct time of day if necessary. If the "Er" message remains, contact a
Servicer.
The ESEC control constantly monitors the internal circuitry as welt as several circuits to
insure they are all operating correctly.
If at any time one of these systems fails, the ESEC
will immediately
stop the current operation and flash an error code of 'F5, F6, or F7" in the
digital display window. If any of these error messages
remain or reappear in the display,
contact a Servicer.
The oven control will only accept correct responses and/or the minimum number of
allowable entries for the appropriate
feature. The oven control is designed to prevent
accidental entries. Review the instructions
in this Use & Care Manual for the feature you are
trying to use. Also review the minimum and maximum temperature
entries for the feature
you are trying to set on page 15 in this Use & Care Manual.
Many factors affect baking results. Make sure the proper rack position is being used. Center
food in the oven and space pans to allow air to circulate. Allow the oven to preheat to the
set temperature
before placing food in the oven. Try adjusting the recipe's recommended
temperature
or baking time. If you feel the oven is cooking too hot or cool, see Adjusting
the Oven Temperature
in this Use & Care Manual.
Self-Cleaning
cycle does not work.
Controis are not set properly. Follow instructions
in the Self-Cleaning
section.
The Self-Clean feature will not operate whenever a radiant surface element is on.
Self-cleaning
cycle was interrupted.
Stop time must be set for 2, 3, or 4 hours past the start
time. Follow steps shown in Stopping
or interrupting
a Self-Clean
Cycle in the Self-
Cleaning
section.
Soil is not completely
removed.
Failure to clean bottom front, top of oven or door areas outside oven seal. These areas are
not in the Self-Cleaning
area, but get hot enough to burn on food residue. Clean these
areas before starting the self-clean cycle. Burned-on
residue may be cleaned with a stiff
nylon brush and water or a nylon scrubber. Be careful not to damage the oven gasket.
Excessive spill-overs
in oven. Set Self-Clean
cycle for a longer Self-Cleaning
time.
Flames inside oven or smoking
Excessive spill-overs
in oven. This is normal, especially for pie spill-overs or large amounts
from vent.
of grease on the oven bottom. Wipe up excessive
spill-overs before starting the self-clean
cycle. If flames or excessive smoke are present, stop the Self-Clean cycle and follow the
steps shown in Stopping
or interrupting
the Self-Clean
Cycle in the Self-Cleaning
section.
36
Advertisement
