Advertisement
OPERATIO
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating your
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask
over the spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING
BRAKE (See Fig. 9)
Your tractor is equipped with an ope rator presence sensing
switch.,
When
engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake wilt shut off the engine.
•
Depress clutch/brake
pedal into full "BRAKE" position
and hold.
o
Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position
Make sure parking brake
will hold tractor secure,
THROTTLE/
CHOKE
CONTROL
ATTACHMENT
CLUTCH LEVER
"ENGAGED"
POSITION
"DISENGAGED"
POSITION
"BRAKE"
PARKING
BRAKE
POSITION
MOTION CONTROL
LEVER
CLUTCHIBRAKE
PEDAL
"DRIVE"
POSITION
"DISENGAGED"
POSITION
"
HEIGHT ADJUSTMENT
KNOB
FIG. 9
STOPPING
(See Fig, 9)
MOWER BLADES -
•
Move attachment clutch lever to "DISENGAGED"
po-
sition_
GROUND DRIVE -
°
Depress clutch/brake pedal into full "BRAKE" position.,
°
Move motion control lever to neutral (N) position.
IMPORTANT:
THE MOT1ON CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSITION WHEN THE
CLUTCH/BRAKE
PEDAL 1S DEPRESSED
ENGINE -
•
Move throttle control to slow (,_,)
position.
NOTE:
Failure to move throttle control to slow (,,_,)
position and allowing engine to idle before stopping may
cause engine to "backfire".
o
Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
o
Never use choke to stop engine..
NOTE:
Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas.
CAUTION:
Always stop tractor
com-
pletely, as described
above, before leav-
ing the operator's
position;
to empty
grass catcher, etc.
TO USE THROTTLE
CONTROL
(See Fig. 9)
Always operate engine at full throttle,
°
Operating engine at less than full throttle reduces the
battery charging rate.
°
Full throttle offers the best bagging and mower perfor-
mance,
TO MOVE FORWARD
AND BACKWARD
(See
Fig. 9)
The direction and speed of movement is controlled by the
motion control lever
°
Start tractor with motion control lever in neutral (N)
position_
•
Release parking brake and clutchlbrake
pedal,
•
Slowly move motion control lever to desired position
TO ADJUST
MOWER
CUTTING
HEIGHT (See
Fig. 9)
The cutting height is controlled by turning the height adjust-
ment knob in desired direction.
=
Turn knob clockwise (f_)
to raise cutting height.,
°
Turn
knob counterclockwise
(_¢--_)to lower cutting
height..
The cutting height range is approximately
t -1/2" to 4". The
heights are measured from the ground to the blade tip with
the engine not running., These heights are approximate
and may vary depending upon soil conditions,
height of
grass and types of grass being mowed.
o
The average lawn should be cut to approximately 2-t/2
inches during the cool season and to over 3 inches
during hot months..
For healthier and better looking
lawns, mow often and after moderate growth,.
°
For best cutting performance, grass over 6 inches in
height should be mowed twice.
Make the first cut
relatively high; the second to desired height..
13
Advertisement
