Table Of Contents; Safety Rules; Operation; Specifications - Craftsman 351.184300 Operator's Manual

Warranty ....................................... 2
Safety Rules .................................... 2
Operation .................................... 2-4
Maintenance .................................... 5
Troubleshooting ................................. 6
Parts Illustration and List ......................... 8-9
Espa_ol .................................... 10-14
FULL ONE YEAR WARRANTY ON CRAFTSMAN
FRAMING NAILER
If this product fails due to a defect in material or workmanship
within one year from the date of purchase, Sears will at its
option repair or replace it free of
charge. Contact your nearest Sears Service Center
(1-800-4-MY-HOME) to arrange for product repair, or return
this product to place of purchase for replacement.
If this product is used for commercial or rental purposes, this
warranty will apply for 90 days from the date of purchase.
This warranty applies only while this product is used in the
United States.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates,
IL 60179
• Air tool operators and all others in work area should
always wear safety goggles complying with United States
ANSI Z87.1 to prevent eye injury from fasteners and flying
debris when loading, operating or unloading this tool.
• Never exceed operating pressure of 110 PSI.
• Always keep hands and body away from the fastener dis-
charge area when air supply is connected to tool.
• Always disconnect tool from air supply when servicing or
adjusting tool and when tool is not in use.
• Do not operate when contact trip is not in contact with
work.
• Never load the tool until you are ready to use it.
• Never depress tool trigger when loading.
• Always load with nose of tool pointing away from you and
others.
• Never point tool at yourself or others.
• Never carry tool with trigger depressed.
• Do not use oxygen, combustible gas or high pressure
compressed gas as the air supply for the tool.
• Always use tool at safe distance from other people in work
area.
• Do not attempt to discharge fastener into hard or brittle
materials such as concrete, steel or tile.
• Do not connect female quick-disconnect coupling to tool
side of air line.
• Connect male, free-flow nipple to tool side of air line
connection so that tool is depressurized when hose is
disconnected.
• Do not use a hose swivel with this tool.
• Use Sears recommended fasteners only.
DESCRIPTION
The Craftsman Framing Nailer drives nails from. 113" to. 131"
diameter and from 2" to 31/2"long. Magazine is angled at 28° for
nailing in tight spots such as when toenailing. High strength
magnesium body and aluminum components are lightweight
and durable. Safety feature disables tool unless contact trip is
pressed against workpiece. Sequential trigger switch allows
selection of rapid-fire or single-fire mode. Contact trip can be
adjusted for setting nail depth. Pusher mechanism supports
shorter fasteners to prevent jamming. Plastic protector on the
end of contact trip prevents marring of workpiece. Large capac-
ity, side load magazine makes it easy to load up to 100 stick
nails at a time. Tool drives straight, screw, and ring shank nails.
Exhaust deflector can be rotated 360 °. The Angle Framing
Nailer is excellent for truss making, framing, sheathing, sub-
flooring and decking.
SPECIFICATIONS
Capacity ............................ 72 to 100 nails
Nail size ............................... 113 to .131"
Nail lengths ............................... 2 to 3W'
Operating pressure ..................... 70 to 110 PSI
Air inlet .................................. 1/4"N.RT.
Length ....................................... 19"
Height ...................................... 141/4 ''
Width ....................................... 51/8"
Weight ..................................... 7 Ibs.
NAILS
18351 ............... 8 penny, .120" diameter x 21/2"long
18352 ............... 10 penny, .120" diameter x 3" long
18353 .............. 16 penny, .131" diameter x 31/S ' long
GALVANIZED NAILS
18357 ............... 8 penny, .120" diameter x 21/S ' long
18358 ............... 10 penny, .120" diameter x 3" long
18359 .............. 16 penny, .131" diameter x 31/S ' long
AIR SUPPLY LINE
Refer to Figure 1 (page 3).
• The air tool operates on compressed air at pressures from
70 to110PSI.
• Never exceed maximum pressure.
Air Delivery Required: 2.21 SCFM @ 90 PSI
(30 shots per minute).
WARNING: Keep hands and body away from discharge area
of tool when connecting air supply. Always disconnect tool
from air supply when servicing or adjusting tool and when tool
is not in use.
• Air operated tools require clean, dry, lubricated com-
pressed air to ensure top performance, low maintenance
and long life.
© Sears, Roebuck and Co.
2