Safety Symbols; Service Safety; Extension Cords - Craftsman 172.34120 Operator's Manual

ELECTRICAL SAFETY cont.
Z_ WARNING:
GFCI (Ground Fault Circuit Interrupter) protection should be
provided on all circuits or outlets to be used for electric chain saws and
lawn and garden power tools. Receptacles are available having built-in GFCl
protection and should be used for this measure of protection.
z_ WARNING:
Double insulation DOES NOT take the place of normal safety
precautions when operating this tool.
Z_ WARNING: Guard against electric shock: Prevent body contact with
grounded surfaces. For example: metal pipes, wire fences.
3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the voltage
marked on the tool's data plate. DO NOT use "AC only" rated tools with a DC power supply.
4. DO NOT expose tools to rain or wet conditions or use electric tools in wet or damp
locations. Water entering an electric tool will increase the risk of electric shock.
5. If operating an electric tool in damp locations is unavoidable, ALWAYS USE a
Ground Fault Circuit Interrupter to supply power to your tool. ALWAYS WEAR
electrician's rubber gloves and footwear in damp conditions,
6. When operating a power tool outside, ALWAYS use an outdoor extension cord marked
"W-A" or "W". these cords are rated for outdoor use and reduce the risk of electric shock.
7. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears Service
Center. BE SURE to stay constantly aware of the cord location and keep it well away
from the cutting blade.
8. DO NOT abuse the extension cord. NEVER use the cord to carry the tool by or to
pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
EXTENSION CORDS
Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL).
Other extension cords can cause a drop in line voltage, resulting in a loss of power
and overheating of tool.
For this tool an AWG (American Wire Gauge) size of a least 14-gauge is recommended
for an extension cord of 25-ft. or less in length. Use 12-gauge for an extension cord
of 50-ft. Extension cords 100-ft. or longer are not recommended,
Remember, a smaller wire gauge size has greater capacity than a larger number
(14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has more capacity
than 14-gauge). When in doubt use the smaller number.
When operating a power tool outdoors, use an outdoor extension cord marked "W-A" or "W'.
These cords are rated for outdoor use and reduce the risk of electric shock.
Z_ CAUTION: Keep the extension cord clear of the work area. Position the
cord so that it will not get caught on bushes, hedges, tree trunks, lawnmowers
or other obstructions while you are working with the Chain Saw.
/_ WARNING:
Check extension cords before each use. If damaged replace
immediately. Never use tool with a damaged cord since touching the damaged
area could cause electrical shock, resulting in serious injury.
6
SAFETY SYMBOLS FOR YOUR TOOL
The label on your tool may include the following symbols.
V ................ Volts
A ................ Amps
Hz.............. Hertz
W ............... Watts
min ............ Minutes
"-4. ............ Alternating current
_: .......... Direct current
no ............ No-load speed
.../rain ....... Revolutions or Strokes per minute
Z_ ............. Indicates danger, warning or caution.
It means attention! Your safety is
involved.
......... Tip contact may cause the guide
bar to move suddenly upward
and backwards, which may cause
serious injury to user.
......... Contact of the guide bar tip with
any object should be avoided.
(_ ......... Read and follow all safety
precautions in the owner's manual
Failure to follow to instruction
could result in serious injury to user.
......... Protective goggles/visor,
helmet & hearing protection.
(_0 Gloves with saw protection.
......... Boots with saw protection,
steel-toe cap and non-slip sole.
[_ ......... Do not use one handed when
operating the chain saw.
[_ ......... Always use two hands when
operating the chain saw.
.......... Class II construction,
Double-Insulation. When servicing,
use only identical replacement parts.
........The chain saw kickback angle
is 10 °, with a chain stop.
......... Correct Direction of Cutting-Teeth.
_/=_ ......... Chain Stop
o\(o)
SERVICE SAFETY
1.
If any part of this Chain Saw is missing or should break, bend, or fail in any way;
or should any electrical component fail to perform properly: SHUT OFF the
power switch and remove the power cord from the Chain Saw and have the missing,
damaged or failed parts replaced BEFORE resuming operation.
2. Tool service should be performed at a qualified service dealer or repair center.
Service or maintenance performed by unqualified personnel could result in a risk of injury.
3. When servicing a tool, use only identical replacement parts. Follow instructions
in the maintenance section of this manual. Use of unauthorized parts or failure to
follow maintenance instructions may create a risk of electric shock or injury.
SAFETY RULES FOR ELECTRIC CHAIN SAWS
1. KNOW your electric Chain Saw. Read operator's manual carefully. Learn the
applications and limitations, as well as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock, fire or serious injury.
2. DO NOT use the Chain Saw without adequate lighting. ALWAYS make sure that you can
see what you are cutting.
3. Use Chain Saw ONLY when wood is dry.
4. ALWAYS stand to the left of the Handle. Any debris thrown by the Chain Saw would be
coming from the Blade Guard area on the right of the Chain Saw.
3/I 4/I 2
Final ART