Advertisement
DESCRIPTION
The Sears Framing Nailer d rives nails of 0 113 to 0..131"
diameter from 2 to 3 1/2" tong. Magazine is angled at
27 1/2 ° for nailing in tight spots such as when toenail-
ing. High
strength,
aluminum
components
are
lightweight and durable. Contact safety disables nailer
until nosepiece is in contact with workptece
Hardened,
serrated contact tip grips wood for fast, easy nailing
Large capacity, top load magazine makes it easy to
load up 105 stick nails at a time. Nailer drives straight,
screw, and ring shank nails. The Sears Angle Framing
Nailer is exce!lent for truss making, framing, sheating,
sub-flooring
and decking.,
. SPECIFICATIONS
Capacity
...............................
75 to 105 nails
Nail Size ..........................
0113 to 0.131"
Nail Lengths
.............................
2 to 3 I/2"
Operating Pressure
.....................
75 to 100 PSIG
Air inlet
........................
1/4" FNRT
Length ...............
. .....................
:18 3/8"
Height ........................................
13 3/4"
Width ......................................
5 1/8"
Weight ................................
8,3 lbs
NAILS
£18351
......
8 penny, .120" diameter x 2 1/2" long
918352
.........
10 penny,. 120" diameter x 3" long
£18353
.....
16 penny, .131"diameter
x 3 1/2"long
SAFETY INSTRUCTIONS
Air tool operators
and all others in work area should
always wear safety goggles
(must comply with ANSl
Z87.1) to prevent eye injury from fasteners and flying
debris when loading, operating
or unloading this tool
Never exceed operating
pressure
of 100 PSlG (7 1
kg/cm 3),,
Always keep hands and body away from the fastener
discharge area when air supply is connected to tool,.
Always disconnect
tool from air supply when servicing
or adjusting toot and when tool is not in use.
Do not operate toot when nose is not in contact with
work,
/_
FILTEr,
- _GLIAT_2
- L_21[A'fl]_
./
J
FENLE DUll[ - I]IS[N,_'E[T
--J
Figure I-
Do not operate tool if contact trip mechanism
is not
functioning
properly
Never load the tool until you are ready to use it.
Never depress tool trigger when loading.
Always load tool with nose pointing away from you and
others.
Never point the tool at yourself or others
Never carry too! with trigger depressed
Do not use oxygen, combustible
gases or high pres-
sure compressed
gas as the air supply for the tool,
Always use tool at safe distance from other people in
work area.
Do not attempt to discharge fastener into hard or brittle
materials such as concrete, steel or tile.
._-Do not connect female quick-disconnect
coupling
to
tool side of air line
Connect male free-flow nipple to tool side of air line so
that tool is depressurized
when
disconnected
from
hose.
Do not use a hose swivel in air supply line,
Use Sears recommended
fasteners only.
OPERATING
INSTRUCTIONS
AIR SUPPLY LINE
Refer to Figure 1.
The Sears Framing Nailer operates on compressed
air
at pressures from 75 to 100 PSIG.
Never exceed maximum pressure.
The minimum
air requirements
for nailer:
Average
working SCFM, 40 at go PSI with a 3/8" air hose and
15 gallon tank
WARNING:
KEEP HANDS AND BODY AWAY FROM
DISCHARGE
AREA OF NAILER WHEN
CONNECTING
AIR SUPPLY. ALWAYS
DISCONNECT
TOOL
FROM AIR SUP-
PLY WHEN
SERVICING,
ADJUSTING
AND WHEN TOOL IS NOT IN USE.
Clean dry air is essential to operation of Sears nailer.
Air operated tools require clean, dry, lubricated
com-
pressed
atr to ensure
top
performance,
tow
maintenance
and long life
Dirt and abrasive materials present in all air lines wilt
damage tool O-rings, valves and cylinders.
/_2
FDD] _ E _HIP
g
I
--2--
Advertisement
