Timer Recording - Sharp DV-RW370X Operation Manual

You can set the unit to record up
to 8 programmes, up to a month
in advance. Daily or weekly
programme recordings are also
available.
• Be sure to set the clock before
entering a timer programming.
Insert a recordable disc or a
tape with a record tab.
1
In stop mode, press
[TIMER PROG.].
Timer Programming list will appear.
Timer Programming
DVD
Date Start End CH
VCR
1. - - -
2. - - -
2
Select a programme that is not
set using [Cursor K / L], then
press [ENTER].
3
Enter the date using [Cursor
K / L], then press [Cursor B].
Timer Programming
DVD
Date Start End CH
VCR
1. 01/01 --:-- --:-- P01
2. - - -
Each time you press [Cursor L]
at the current date, the timer
recording date will change as
follows.
e.g., 1st January
01/01
Daily
M-F (Mon.-Fri.)
W-SAT
W-FRI
W-SUN
31/01
Recording

Timer Recording

4
Enter the time to start and to
end using [Cursor K / L], then
press [Cursor B].
Timer Programming
Date Start
1. 01/01 12:00
2. - - -
5
Select the channel number to
record using [Cursor K / L],
then press [Cursor B].
Timer Programming
Date Start
1. 01/01 12:00
2. - - -
To record from the external input,
select "AV1", "AV2", or "AV3".
VCR DVD
Mode 6
Select the recording media
("DVD" or "VCR") using [Cursor
K / L], then press [Cursor B].
Timer Programming
Date Start
1. 01/01 12:00
2. - - -
7
Select the recording mode using
[Cursor K / L]. (See page 24.)
VCR DVD
Timer Programming
Mode
Date Start
1. 01/01 12:00
2. - - -
Note
• If you have not set the clock, the clock setting window will appear
instead of the Timer Programming list. Continue from step 4 in "Clock
Setting" on page 22 before programming the timer.
• Press [Cursor { / B] to move the cursor in the Timer Programming list.
• If a basic recording or One-touch Timer Recording is in progress on
one component (e.g. VCR) and the timer recording set for the other
component (e.g. DVD) is about to begin, the unit automatically
switches to the programmed channel for timer recording 2 minutes
before the programmed starting time, and the recording in progress
(for VCR) will be cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the timer recording
will start without cancelling the recording currently in progress. In this
case, the recording of the same channel will be made on both DVD
and VCR.
• Cancel the timer-standby mode by pressing [T-SET] before operation
for either DVD or VCR. When finished operating, press [T-SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the power and use the
component (VCR or DVD) which is not currently timer-programmed.
8
Press [ENTER] when all informa-
tion required is entered.
Your programme setting is
stored.
VCR DVD
• To set another programme,
DVD
End CH Mode
VCR
--:-- P01
• To exit, press [TIMER PROG.].
• If the recording times of two
VCR DVD
9
DVD
End CH Mode
VCR
Press [T-SET].
13:00 P01
The
front panel display and the unit
enters to the timer-standby
mode.
9
VCR DVD
DVD
End CH Mode
VCR
13:00 P01 DVD
VCR DVD
DVD
End CH Mode
VCR
13:00 P01 DVD XP
repeat steps 2 to 8.
or more programmes overlap,
"Overlap" and overlapped
programme numbers are
displayed. (See pages 32-33.)
icon will appear on the
OPERATE
OPEN/CLOSE
DUBBING SETUP EJECT
T-SET TIMER PROG. REC MODE RAPID PLAY
VCR DVD
CM SKIP
ZOOM
TOP MENU MENU LIST
RETURN ENTER
.@/: ABC DEF
1 2 3
PROG.
GHI JKL MNO
4 5 6
PQRS TUV WXYZ
7 8 9
SKIP
CLEAR/C-RESET SPACE DISPLAY
0
REV FWD
PLAY
VCR DVD
REC/OTR REC/OTR
STOP
1
8
2
3
4
5
6
7
8
EN 31