Advertisement
NEC Plasma PX-42/50/60/61, VM/VP/VR/XM/XR, 2/3/4/5/6 (Code: 14hex)
This family has many members with a range of channel messages.
There is a typical RS232 code Operation Manual at:
And
http://www.nec-display-solutions.co.uk/c/g/uk/en/Service/Home/index.html
Channel codes are:
Computer1 := DF + 80 + 60 + 47 + 01 + 07 + 0E;
Computer2 := DF + 80 + 60 + 47 + 01 + 08 + 0F;
Computer3 := DF + 80 + 60 + 47 + 01 + 0C + 13;
Video1
:= DF + 80 + 60 + 47 + 01 + 02 + 09;
Video2
:= DF + 80 + 60 + 47 + 01 + 03 + 0A;
Video3
:= DF + 80 + 60 + 47 + 01 + 01 + 08;
Video4
:= DF + 80 + 60 + 47 + 01 + 05 + 0C;
Video5
:= DF + 80 + 60 + 47 + 01 + 06 + 0D;
Video6
:= DF + 80 + 60 + 47 + 01 + 0E + 15;
Video7
:= DF + 80 + 60 + 47 + 01 + 1A + 21;
Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video
codes. (The default is to have Computer1 (above) as the "Computer" channel and Video1 as the "Video" channel.
Setting OPT1 switch ON will swap Video1 and Video2 channels, making S-Video the video default.)
This panel can be used with a number of keyboards:
With a "Code 9" keyboard, with buttons selecting "Video" and 'Computer", with "Volume" keys.
•
With a "Code B-L" or "Code B-P" keyboard, with buttons selecting "Video" and "Computer1" and "Computer2"
•
with "Volume" control keys. (Keyboards combine channel keys with "On" keys.)
(There is no point in using a Code A keyboard, as there is no "Freeze" function on plasma screens.
•
Panel connection blink codes are available but OPT7 handshake mode in NOT.
Audio mute with 2 Vol keys is available, but not video.
RS232 connections to NEC Plasma with D9
These use a 9-pin-D9 male on the plasma, female on cable. Comms is at 9600 baud, 8 bits, Odd parity, 1 stop.
Function/Direction
Ground
Data from T440 to projector
Reply data from projector to T440
Plus 9 volt CTS/DTR to projector
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins
in any installation, as described in the troubleshooting part of this manual.
T440 Users manual V021/B, © JED Microprocessors Pty Ltd Nov 17th 2008
http://www.prokare.com.tr/pdf2/nec_residental_plasma_rs232.pdf
// RGB1 / PC1 DB15
// RGB2 / PC2 5 x BNC
// RGB3 / PC3 DVI-D
// "Video2" RCA Composite Video
// "Video3" S-VIDEO DIN-4
// "Video1" BNC
// HD1 3 x RCA DTV1/Component
// HD2 5 x BNC DTV2/Component or SCART1/2
// HD3 DVI/HDMI (some only)
// HD4 DVD/HDMI (some only)
T440 "projector"
"Serial" Port Connector
Connection
Ground
9-pin D-sub pin 5
Tx
9-pin D-sub pin 2 (RXD)
Rx
9-pin D-sub pin 3 (TXD)
"RTS"
9-pin D-sub pin 8(CTS IN)
1
2
3
4
5
6
7
8
9
D-sub 9 female
solder side
Page 14
Advertisement
