Download Print this page

JED T440 User Manual

Simple projector controller
Hide thumbs Also See for JED T440:

Advertisement

Quick Links

JED T440 Simple Projector Controller users manual version V021 part B
(Ed Schoell rev: Nov 17th 2008)
Acer projector family
BenQ MP5/7xx, SP820,Opt Gr3
Epson VP21, IR to X5
HP projector
Hitachi proj
InFocus / ASK Proxima
LG LCD/Plasma TV
Mitsubishi
NEC LCD TV (& Sherwood), Plasma
and NEC Projector
Acer (Code 70 hex), PD727, P1165, P1265, P5260, P5270, P5280, P5370
Channel codes are:
Computer1
:= '* 0 IR 015' + 0D;
Computer2
:= '* 0 IR 028' + 0D;
Computer3
:= '* 0 IR 016' + 0D;
Video1
:= '* 0 IR 019' + 0D;
Video2
:= '* 0 IR 018' + 0D;
Video3
:= '* 0 IR 017' + 0D;
Video4
:= '* 0 IR 029' + 0D;
Video5
:= '* 0 IR 016' + 0D;
(There may be more codes available for "Wireless" and "HDMI" on newer devices. Update later.)
Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video
codes. (The default is to have Computer1 (above) as the "Computer" channel and Video1 as the "Video" channel.
Setting OPT1 switch ON will swap Video1 and Video2 channels, making S-Video the video default.)
Power on projector connection blink codes available;
OPT7 handshake mode not available;
Source lock must be turned ON in the "Maintenance" menu;
Freeze and mute are toggle mode only in these projectors, so 2-yellow-button mute mode is NOT supported;
Audio functions are limited to one (sometimes two) audio input(s) and no output to room speakers. Use a T461 if
audio control is needed.
RS232 connections to 3-Pin DIN Acer projectors.
Mini-DIN 3 socket on projector. Coms at: 9600 DP8N1
Function/Direction
Ground
Data from T440 to projector
Reply data from projector to T440
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins
in any installation, as described in the troubleshooting part of this manual.
T440 Users manual V021/B, © JED Microprocessors Pty Ltd Nov 17th 2008
Table of Contents
1
Optoma Projector Gr1&2
2/3
Panasonic Projector
4/5
Plus U5, U7 Projector
6
Sanyo LCD TV, projector
7
Sharp
8
Sony projector
9
Toshiba projector
10/11
Taxan projector
12/15
// RGB analog-RGB VGA
// RGB analog- via DVI (some models only)
// DVI digital via DVI
// Comp Video
// S-Video
// Component YPbPr via DB15 HDTV
// Component YPbPr DVI or HDMI via adaptor (some models only)
// DVI or HDMI via adaptor
T440 "projector"
Connection
Ground
Tx
Rx
16/17
18/19
20
21/23
24
25
26/27
28
Acer Serial Port
Connector
Mini-DIN 3 pin 3 (Gnd)
Mini-DIN 3 pin 1 or 2 (RXD)
Mini-DIN 3 pin 2 or 1 (TXD)
1
2
3
Mini-DIN 3
solder side
Page 1

Advertisement

loading

Summary of Contents for JED JED T440

  • Page 1 Reply data from projector to T440 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 2 Even though some BenQ manuals show a D sub 9 connector, the tested projectors all have mini-DIN 8-pin sockets. After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 3 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 4 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 5 (after warm-up) will index the projector through available sources, but it will only stop on a source if a valid input is being fed into that input when the projector is looking at that channel. If there is no input at that point, it will not change to it, but just put up a message screen.
  • Page 6 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 7 Plus 9 volt CTS/DTR After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. CTS is NOT needed.
  • Page 8 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 9 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 10 SD105U, S/XD206U: Some model types for code group 28 hex, no audio or inc/dec audio only range: If there is no “Volume commands” paragraph (or no audio in the projector), use the incremental control driver selection, code $28. No audio: HC1100, HC1500, HC3000, HC3100, HC4900, HC5000, HD1000, HD4000...
  • Page 11 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 12 Reply data from projector to T440 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 13 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 14 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 15 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 16 Reply data from projector to T440 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 17 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 18 Mute and freeze keyboard code A available; • Make sure to turn off “Auto input search” if your projector includes this; • Make sure to set the baud rate to 9600 and no parity if an adjustment menu is provided.
  • Page 19 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 20 CR with the ENTER key, and send the LF by holding down CTRL and pressing ENTER.) The projector should reply with its status, eg #QS2 if OFF, and #QS6 if warmed up and running. If, OFF, the projector can be turned ON with the #P1(CR)(LF) command.
  • Page 21 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 22 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 23 Reply data from projector to T440 Plus 9 volt CTS/DTR to projector Note: The signal input and output of this projector has clamp diodes and never goes below –0.7 volts or over +5.7 volts, even when connected to the T440.
  • Page 24 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 25 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 26 Toshiba (Codes $50 to $54 hex) A good collection of protocol manuals is at: http://www.isd.toshiba.com.au/projectors/projectors/service-manuals.shtml Code $50: (Group 1.1): TLP-S200/S201/S220/S221, TLP-T400/T401, TLP-T500/T501/T520/T521, TLP- T600/T601/T620/T621, and TLP-T700/T701/T720/T721; Code $51 (Group 1.2): TDP-MT200/MT400; Code $51 (Group 1.3): TDP-S20/S21/SC21/S25/SC25/SW25/S35/SC35/SW35, TDP-S80/SW80/S81/T90/TW90/T91/T99/TW99, and TLP-710/711; Code $51 (Group 1.4): TDP-S8/S10, SW20, TDP-T8/T9/T30/T40/T45/T80/T98, TLP-250/251/260/261/380/381/550/551/560/561/780/781/790/791, TLP-MT7E, TLP-X10U/11U/20U/21U;...
  • Page 27 Plus 9 volt CTS/DTR to projector After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual.
  • Page 28 To determine what line is what, measure the voltage on pins 2 and 3. If a pin has -5 to -9 volts on it is an output from the projector and should be connected to the RX output on the T440. The other line into the projector should have a resistance to ground of about 5kohm.