Step 3. Auto Programming Your Tv; Step 4. Subscribing To Starsight - Zenith SR2745 Operating Manual & Warranty

INSTALLING STARSIGHT
STEP 3. Auto Programming Your TV.
Auto Program lets your TV know what channels are
available via antenna or cable. For StarSight to function
properly, you must complete this step.
le
2;.
Your TV comes equipped with two remote controls--
a trackball type and a multibrand conventional type.
Use the MBR3462 Multibrand Remote for this
procedure.
Press TV at the top of the multibrand remote. Then
press TV/VCR SOURCE. At the top of the TV screen,
five menus are displayed: SOURCE, SETUP,
AUDIO, VIDEO, and PiP. Use UP ARROW and
DOWN ARROW to highlight ANT/CABLE 1 and
press ENTER/TUNE. Now press MENU/GUIDE
twice. SETUP is highlighted. Use UP ARROW and
DOWN ARROW to highlight AUTO PROGRAM.
Press LEFT ARROW or RIGHT ARROW. On the
next screen, select OFF AIR ANTENNA or CABLE
BOX by pressing UP ARROW or DOWN ARROW.
If you used Setups 1 or 3 with cable, select CABLE
TV.
4.
5.
6.
Make sure that your cable box is turned on and that
your VCR is turned off. Press LEFT ARROW or
RIGHT ARROW to begin AUTO PROGRAM.
When AUTO PROGRAM is complete, it indicates the
number of channels found, and after a short period,
the TV returns to normal viewing.
STEP 4. Subscribing to Starsight
To bring StarSight information into your home, you must
subscribe to StarSight. You start the process directly
through your I-'V, in a series of easy steps that take only
mintttes.
First, you must be sure that you:
• have completed the Subscription Checklist.
• [lave followed the step-Sy-step installation
instructions on the preceding pages thai: apply to
3,our video equipment.
• have your Zenith/StarSight nmltibrand remote
control handy.
• have a videotape ready that you can use for a
30-second recording test (if you have a VCR).
• have a telephone nearby to call StarSiglat's toll-free
subscription number: 1--800-643-STAR.
How to Subscribe to StarSight:
le
•
Perform this step only if you have a Cable System and
used Setup 4. Otherwise, skip to step 7.
Press the TV buttton near the top of the remote. You
must now AUTO PROGRAM ANT/CABLE 2. Press 3.
TV/VCR SOURCE. Press DOWN ARROW to
highlight ANT/CABLE 2. Press ENTERfFUNE. 4.
Next, press MENU/GUIDE twice to highlight
SETUP. Use UP ARROW to highlight
AUTOPROGRAM. Press RIGHT ARROW. When
AUTO PROGRAM is completed, press TV/VCR
SOURCE and then UP ARROW to return to
ANT/CABLE 1. 5o
If you have a Cable Box, make sure that it is; tuned to
the PBS channel listed on the Subscription Checklist.
If you do not have a Cable Box, be sure that your TV
is tuned to the correct FBS channel. StarSight will
search for schedule inRmnation on this charmel.
7. Press STAR to enter StarSight mode.
8. Proceed to "Step 4. Subscribing to StarSight."
Press STAR on your Zenith multibrand remote control
to get into StarSight mode.
The StarSight Menu will 9e displayed with "Activate
for StarSight" highlighTer.
Press ENTER/TUNE
to begin subscription. Then
follow the on-screen instructions.
°
StarSight will ask you about your equipment, search
for schedule informatien on your PBS station and
display your STAR # and ID #. (Enter these numbers
in paragraph "C" of your Subscription Checklist.) You
will also be asked to call StarSight.
The StarSight representative will ask yc,u for some
subscriber information, and will authorize you to
receive StarSight.
When you have been authorized, you'll see a screen
that says: Congratulations';!
I
YOU SHOULD ALSO KNOW...
• If no schedule data is found, you may be tuned to the wrong PBS station. Check the FBS station written on your
Subscription Checklist and try again. Or, try tuning to a different PBS station that is lisled for your area in the
'q-ESTING STARSIGHT" Section. (If no station is listed for your area, call 1-800-628-STAR for further information.)
1-6