Advertisement
..IAFTSMAN
CIRCULAR
SAW--MODEL
NUMBER
315.11870
Fig. 4
Fig. 5
\
Fig, 6
DEPTH OF CUT--freer
depth
adjustment
should
permit only one tooth of the blade to proie_ below the
material
to be cut. (For carbide tipped
blades, only
of.a tooth.) Depth adjustment
should allow only
the minimum
blade exposure beyond maximum thick-
ness of material
to be cut, More depth will an/y in-
crease friction and make for a rough cut. To adjust
depth of cut (See Fig. 3) loosen knob (A), grasp han-
dle, bold rear of base against flat surface
and raise
un_ until required depth is reached, Tighten
knob h)
lock,
A setting approximately
Ya inch d_pper than
thickn_se of material to be cat is recommended for
best perfarn_nce.
Depth setting should 'be at max/-
mum
depth
when performing
blade
installation
or
change-over.
T° CROSS CUT AND
RiP CUT--The
guide
(llne
where bose and outboard base meet or edge of base
when outboard bcue is removed) is in line with sew
blade when .b_.velsetting is at 0 °. Inner face of notch
in base is guide when bevel setting is at 45 ° . At inter_
mediate settings blade will cut slightly to the left of
the guide edge. To compensate offeatyonr
guide line
to the right on the board to be cut.
The rip guide provided with your sew will assist you
in making rip cuts of up to 5_
inches. (See Pig. 4)
Outboard bose must be removed I_fose assembling rip
gmae.
I/VtPORTANT_EE
SURE POWER CORD
IS-
DISCONNECTED
FROM
POWER SUPPLY.
Lo_en
knurled head screw IB) by turning conntemlockwise
and remove outboard base. Insert rip guide (A) under
clamp bracket (C) and adjust to desired setting
with
graduated
surface up.
Tighten knurled head screw
in clamp bracket securely. Outboard base may also
be removed for closer cutting parallel to walls etc.
Closest cutting
will be accomplished with bevel set-
_ng at 0 °.
H01d• guide
face
firmly
against
right
edge
of wnrk
to obtain
a true cut
without
cramping
the blade.
Guiding
edge of work
must he streight
for desirable
results
when
using rip guide.
Us_ caution
to prevent
• • blade from
binding
in the kerf at end of a cut.
TO BEVEL CUT,-**-_..True a ngle of cat may be adjusted
to anydesired setting between 0 ° and 45 °. (See Fig. 5)
IMPORTAHT_EE
SURE POWER CORD IS DISCON-
NEC'TED FROM POWER SUPPLY. Loosen knobs and
adjust base so that index mark (B) is at O°, Tighten
knob (A) (See Fig. S). Set desired depth
of cut and
tighten knob U_) (See Fig. 3), Set index mark (B) in
line with _requirod angle setting on bevel scale and
tighten
knob (A) (See Fig. 5), After setting at requir-
ed angle make a tria.I cut in scrap material along a
guide line to determine
how much if any guide line
must be offset to produce desirable cut.
TO POCKET
CUT---(See
Fig. 6) With
bevel
setting
at
0
swing
k_war blade
guard
up and
hold,
rest frQnt
of base fiat on work-piece.
Sta_
unit end slowly lower
blade into work moving
unit steadily
forward
to allmr
rh, ing knife
to move
into kerr
until
base is fiat
on
york.
After
cut is complete,
release
switch and allow
blade
to come to a complete
step bob)re
removing
from work.
CoreenD my
be cleaned
out
with e hand
sew
or sebre
sew.
Page5
Advertisement
