Craftsman 3one 917.252580 Owner's Manual page 13

OPERATmON
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating your
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask
over the spectacles or standard safety glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your tractor is equipped with an operator presence sensing
switch When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine,
= Depress clutch/brake pedal into full "BRAKE" position
and hold,
Place parking brake lever in "ENGAGED" position and
release pressu re from clutch/brake pedal. Pedal should
remain in "BRAKE" position Make sure parking brake
will hold tractor secure.
STOPPING (See Fig. 8)
MOWER BLADES +
• Move attachment clutch switch to "DISENGAGED"
position,
GROUND DRIVE -
Depress clutch/brake pedal into full "BRAKE" position.
° Move gearshift lever to neutral (N) position+
ENGINE -
° Move throttle control to slow () position.
NOTE: Failure to move throttle control to slow 0 position
and allowing engine to idle before stopping may cause
engine to "backfire".
o Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use+
Never use choke to stop engine+
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas+
++,+to oom J
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc+
TO USE THROTTLE CONTROL (See Fig. 8)
Always operate engine at full throttle,
Operating engine at less than full throttle reduces the
battery charging rate+
o Full throttle offers the best bagging and mower perfor-
mance+
TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
The direction and speed of movement is controlled by the
gearshift lever
Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position+
• Move gearshift lever to desired position.
o Slowly release clutch/brake pedal to start movement,
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE+
ATTACHMENT
THROTFL_ CLUTCH SWITCH
CHOKE PUSH-INTO PULL-OUTTO
CONTROL "DISENGAGE .... ENGAGE"
_EIGHT
ADJUSTMENT
KNOB_
"BRAKE"
POSITION GEARSHIFT
CLUTCH/BRAKE
PEDAL "DRIVE"
POSITION
PARKING
BRAKE
"DISENGAGED .... ENGAGED"
POSITION POSITION
FIG. 8
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)
The cutting height is controlled by turning the height adjust-
ment knob in desired direction.
Turn knob clockwise ((_d) to raise cutting height
• Turn knob counterclockwise (_'_)to lower cutting
height+
The cutting height range isapproximately 1-1/2" to 4" The
heights are measured from the ground to the blade tip with
the engine not running These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed,
° The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months_ For healthier and better looking
lawns, mow often and after moderate growth
° For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height,
13