[] Unpacking; [] Features; Switch; Lock-On Button - Craftsman 315.175040 Owner's Manual

Your muter has been shipped completely assembled and
ready for use. Inspect it car fully to make sure no breakage
or damage has occurred during shipping. If any parts are
damaged or missing, contact your nearest Sears Retail
Store to obtain replacement parts before attempting to
operate router. A wrench and this owner's manual are also
included.
i
WARNING:
If any parts are missing, do not operate your router until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
SWITCH
T_otum your router ON, depress the switch trigger. Release
switch trigger to turn your router OFF.
LOCK-ON BUTTON
The switch of your router is equipped with a lock-on feature
which is convenient when operating for extended periods of
• time. To lock on, depress the trigger, push in the lock button
located on the side of the handle, then while holdingthe lock
button pushed in, release the trigger. To release the lock,
depress the trigger and release it.
WARNING:
Before connecting your router to power supply sour e,
always check to be sure it is not in lock-on position
(depress and release switch trigger). Failure to do so
could result in accidental starting of your muter resulting
in possible serious injury. Also, do not lock the trigger on
jobs where your muter may need to be stopped suddenly.
i
CHIP SHIELD
A clear plastic chip shield is installed on the front of your
router for protection against flying dust and chips. The shield
isdesigned to fit the opening of the muter base. If necessary
to remove chip shield, squeeze the tabs on each end and pull
outward. To replace, squeeze the tabs at each end, fit into
-opening, thenrelease. NOTE: Model No. 315.175060 has a
chip shield on the front and rear opening of the router base.
For your protection, do not use router without chip
sh!eld(s) properly in place. Ifdesired, the horsepower label
can be removed from chip shield by simply peeling off.
WRENCH STORAGE AREA
Your router has a wrench storage area located on the top end
cap portion of the motor IlOusing.When installing or removing
cutters, remove the wrench from its storage area. Proper
storage of wrench when not in use will help reduce the
possibility of losing wrench.
VARIABLE SPEED SWITCH WITH ELECTRONIC
SPEED CONTROL
(MODEL NOS. 315.175050 AND 315.175060 ONLY)
See Figures lb and lc.
Yol_q_outel_as advanced electronic features, designed to
assist you in getting the maximum use from your router. By
making pr perspeed selections, your muter can be adjusted
to specific routing needs. This eliminates much of the guess
work previously needed to perform a given job. Both the
experienced and inexperienced router users benefit,
obtaining pr fessional like results with fewer job err rs.
The variable speed control allows the router speed to be
adjusted from 15,000 to 25,000 rpm. The variable speed
control selector is conveniently located outside the right
handle near the operator's thumb or hand.
Speed can be set according to the approximate cutter
diameter you will be using and to the hardness of the
material being cut. The best cuts are made when the cutter
is fed thr ugh material at the proper rate of feed.
DUST BAG ASSEMBLY
(MODEL NO. 315.175060 ONLY)
See Figure lc.
The dust bag located on the side of your muter provides a
dust collection system for your router. For more efficient
operation, empty dust bag when half full.
Do not connect r uterto power supply before installing dust
bag or connecting it to a dust collection system.
WARNING:
To prevent the possibility of sawdust or foreign objects
being thrwn into your face and eyes, never attempt to
use your router without dust bag propedy installed.
Sawdust or foreign objects being thrwn intoyour face or
eyes could result in possible serious injury.
i
TO INSTALL DUST BAG:
The dust bag should be installed by slippi_j it v_th a twisting
motion over the blower exhaust. The bag should be installed
with the zipper down when router is in upright positiori.
TO EMPTY DUST BAG:
Remove dust bag from router, open zipper and shake out
dust. Occasionally turn the dust bag inside out and brash the
accumulation of dust from the inside of the bag. This will
allow the air to flow thr ugh the bag better.
Page 7