Model W1781 21˚ Framing Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
Page 4
Model W1781 21˚ Framing Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before servicing, changing accessories, or tool. Make sure your air hose is in moving to another location. good condition and is long enough to reach your work without 18.
Model W1781 21˚ Framing Nailer Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work...
We stand behind our tools! In the event that questions arise about your tool, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. Our Read the manual before operation.
Model W1781 21˚ Framing Nailer Compressed Air System The Model W1781 is designed to be operated at 80-110 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer, regulate the air pressure to find the optimum setting within the specified operating range.
Page 8
Model W1781 21˚ Framing Nailer SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1781. Lay the components out to inventory them.
Page 9
Model W1781 21˚ Framing Nailer Safety Nose Mechanism — If you find that the safety nose mechanism is not working A safety mechanism on the nose of properly, check the lubrication of the nailer protects against accidental its sliding components. firing.
Page 10
Model W1781 21˚ Framing Nailer OPERATIONS Loading 4. Slide the nails all the way down to the nose of the nailer. When replacing nails in your Model W1781, follow these guidelines: 5. With one hand on the magazine handle for control, release the Type: ......
Model W1781 21˚ Framing Nailer Adjusting Depth 3. Depress the safety nose mechanism against your workpiece. A depth adjustment knob is attached to 4. Before pulling the trigger, make sure the nose for setting the nail depth. your free hand and other body parts To adjust the depth, do these steps: are positioned out of the way of a potential path of a nail in case of...
Model W1781 21˚ Framing Nailer Clearing Jammed Nails Replacing Pistons and O-Rings A jammed nail must be cleared before using the nailer again. Under heavy use, a piston or piston shaft may wear out. Replacement is quick and To clear a jammed nail from the dis- easy.
Page 13
Model W1781 21˚ Framing Nailer 6. Open the nose cover as if to clear a 10. Insert the new piston in the cylinder. jammed nail. Make sure that the grooves on the piston shaft line up with those on the 7.
Model W1781 21˚ Framing Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the nailer. Always be sure included with your new Shop Fox nailer that the nailer is dry before using it to help maintain its useful life.
Model W1781 21˚ Framing Nailer Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at trig- 1. O-rings in trigger valve 1. O-rings must be replaced ger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking 1.
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
Page 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...