Shop fox  W1774 Owner's Manual
Shop fox  W1774 Owner's Manual

Shop fox W1774 Owner's Manual

18 gauge brad nailer
Hide thumbs Also See for SHOP FOX W1774:

Advertisement

Quick Links

MODEL W1774
18 GAUGE BRAD NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9551TS Printed in China

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SHOP FOX W1774 and is the answer not in the manual?

Questions and answers

Summary of Contents for Shop fox SHOP FOX W1774

  • Page 1 OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use.
  • Page 3: Safety Instructions For Pneumatic Tools

    Model W1774 18 Gauge Brad Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
  • Page 4 Model W1774 18 Gauge Brad Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before servicing, changing accessories, or tool. Make sure your air hose is in moving to another location. good condition and is long enough to reach your work without 18.
  • Page 5 Model W1774 18 Gauge Brad Nailer Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work...
  • Page 6: Woodstock Technical Support

    Operating Pressure ....60–100 PSI and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is commit- ted to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.
  • Page 7: Compressed Air System

    Model W1774 18 Gauge Brad Nailer Compressed Air System The Model W1774 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range.
  • Page 8 Model W1774 18 Gauge Brad Nailer SETUP Unpacking This brad nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1774. Lay the components out to inventory them.
  • Page 9 Safety Nose Model W1774 18 Gauge Brad Nailer Safety Nose Mechanism — If the nailer fires when the trigger is pulled, without the safety nose A safety mechanism on the nose of mechanism being depressed, then the nailer protects against accidental the nailer is not working properly.
  • Page 10 Model W1774 18 Gauge Brad Nailer OPERATIONS Loading When replacing nails in your Model W1774, follow these guidelines: Gauge: ........18 Length: ........⁄ "–2" Capacity: ........100 To load your nailer, do these steps: Figure 3. Loading nails into magazine. 1.
  • Page 11 Model W1774 18 Gauge Brad Nailer 3. Depress the safety nose mechanism 5. Pull the trigger. against your workpiece. — If the nail drove into the wood 4. Before pulling the trigger, make sure far enough, continue with your your free hand and other body parts intended operations.
  • Page 12: Clearing Jammed Nails

    Model W1774 18 Gauge Brad Nailer Clearing Jammed Nails ���������� A jammed nail must be cleared before using the nailer again. ����������� To clear a jammed nail from the dis- charge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Figure 5.
  • Page 13: Replacing Pistons/O-Rings

    Model W1774 18 Gauge Brad Nailer Replacing Pistons/ 6. Open the nose cover as if to clear a jammed nail. O-Rings 7. Watch the discharge area and push Under heavy use, a piston or piston shaft the top of the piston with your may wear out.
  • Page 14: Cleaning And Lubrication

    Model W1774 18 Gauge Brad Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Use a quality pneumatic tool oil with your assembly of the nailer. Always be sure new Shop Fox nailer to help maintain its that the nailer is dry before using it useful life.
  • Page 15 Model W1774 18 Gauge Brad Nailer W1774 PARTS BREAKDOWN -13-...
  • Page 16 Model W1774 18 Gauge Brad Nailer W1774 PARTS LIST REF PART�# DESCRIPTION REF PART�# DESCRIPTION X1774101 SPECIAL�BOLT X1774136 COMPRESSION�SPRING X1774102 EXHAUST�PORT X1774137 SAFETY�NOSE X1774103 COMPRESSION�SPRING X1774138 DRIVER�GUIDE XPB42M HEX�BOLT�M5-.8�X�20 X1774139 SPACER XPLW01M LOCK�WASHER�5MM XPSB15M CAP�SCREW�M5-.8�X�20 X1774106 CYLINDER�CAP XPSB23M CAP�SCREW�M4-.7�X�12 X1774107 O-RING�13.7�X�2.4 XPSB17M CAP�SCREW�M4-.7�X�10...
  • Page 17: Troubleshooting

    Model W1774 18 Gauge Brad Nailer Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking between 1.
  • Page 18 �������������������� ������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ����������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ��������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������� ����������������������������������������������������������� ����������������������������������������������������������������������������������� ���������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������ ���������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������ �������������������������������������������������������������������������������������� ��������������������������������������� ����������������������������������������������������������������������������� �����������������������������������������������������������...
  • Page 19: Warranty Registration

    Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
  • Page 20 FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...

Table of Contents