Shop fox  W1777 Owner's Manual
Shop fox  W1777 Owner's Manual

Shop fox W1777 Owner's Manual

2 1/2" 16 gauge finish nailer

Advertisement

Quick Links

MODEL W1777
2
" 16 GAUGE
1
2
FINISH NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9552TS Printed in China

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SHOP FOX W1777 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Shop fox SHOP FOX W1777

  • Page 1 OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use.
  • Page 3: Safety Instructions For Pneumatic Tools

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
  • Page 4 Model W1777 2 ⁄ " 16 Gauge Finish Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before servicing, changing accessories, or tool. Make sure your air hose is in moving to another location. good condition and is long enough to reach your work without 18.
  • Page 5 Model W1777 2 ⁄ " 16 Gauge Finish Nailer Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece,...
  • Page 6: Woodstock Technical Support

    Operating Pressure ....60–100 PSI parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is commit- ted to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.
  • Page 7: Compressed Air System

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer Compressed Air System The Model W1777 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range.
  • Page 8 Model W1777 2 ⁄ " 16 Gauge Finish Nailer SETUP Unpacking This finish nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1777.
  • Page 9 Model W1777 2 ⁄ " 16 Gauge Finish Nailer Safety Nose Mechanism — If the nailer fires when the trigger is pulled, without the safety nose A safety mechanism on the nose of mechanism being depressed, then the nailer protects against accidental the nailer is not working properly.
  • Page 10 Model W1777 2 ⁄ " 16 Gauge Finish Nailer OPERATIONS Loading When replacing nails in your Model W1777, follow these guidelines: Gauge: ........16 Length: ......1 ⁄ "–2 ⁄ " Capacity: ........74 To load your nailer, do these steps: Figure 3. Loading nails into magazine. 1.
  • Page 11: Adjusting Depth

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer Adjusting Depth 3. Depress the safety nose mechanism against your workpiece. A depth adjustment knob is attached to 4. Before pulling the trigger, make sure the nose for setting the nail depth. your free hand and other body parts To adjust the nail depth, do these are positioned out of the way of a...
  • Page 12: Clearing Jammed Nails

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer Clearing Jammed Nails Nose Release Nose A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the dis- charge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR Nose Cover SUPPLY! Figure 6.
  • Page 13: Replacing Pistons/O-Rings

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer Replacing Pistons/ 6. Open the nose cover as if to clear a jammed nail. O-Rings 7. Watch the discharge area and push Under heavy use, a piston or piston shaft the top of the piston with your may wear out.
  • Page 14: Cleaning And Lubrication

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the nailer. Always be sure included with your new Shop Fox nailer that the nailer is dry before using it to help maintain its useful life.
  • Page 15 Model W1777 2 ⁄ " 16 Gauge Finish Nailer W1777 PARTS BREAKDOWN -13-...
  • Page 16 Model W1777 2 ⁄ " 16 Gauge Finish Nailer W1777 PARTS LIST REF PART�# DESCRIPTION REF PART�# DESCRIPTION XPAW05M HEX�WRENCH�5MM 49 X1777049 STEEL�BALL�DW=2 XPAW04M HEX�WRENCH�4MM 50 X1777050 SPECIAL�SCREW X1777003 CARRYING�CASE 51 X1777051 SUPPORT�BRACKET X1777004 AIR�PLUG�COVER 52 X1777052 CONNECTING�BRACKET X1777005 AIR�PLUG 53 X1777053 ROLL�PIN�3�X�28 X1777006 END�CAP 54 X1777054 O-RING�2�X�2.5...
  • Page 17: Troubleshooting

    Model W1777 2 ⁄ " 16 Gauge Finish Nailer Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking between 1.
  • Page 18 �������������������� ������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ����������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ��������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������� ����������������������������������������������������������� ����������������������������������������������������������������������������������� ���������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������ ���������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������ �������������������������������������������������������������������������������������� ��������������������������������������� ����������������������������������������������������������������������������� �����������������������������������������������������������...
  • Page 19: Warranty Registration

    Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
  • Page 20 FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...

Table of Contents