Step 7: Additional Adjustments - Sony BDP-S1 Operating Instructions Manual
Blu-ray disc player
Hide thumbs
Also See for BDP-S1:
- Operating instructions manual (71 pages) ,
- Specifications (2 pages) ,
- Technical information (1 page)
Table of Contents
Advertisement
_70IUSOt
book Page 20 Tuesday,_S-_._,_}_\_843_:_'SiOS
BDP.S 1\1024\2687794111
BDP-S1 (US) 1006\2687794111
BDPSI\01US05GET.fmmaster:Left
_l
Select the aspect ratio that matches
your TV,
and press ENTER.
+
4, If youhavea wide screenTV or a 4:3 standardTV
with a wide screen mode
Select "16:9" (l)age 45).
<_ If you have a 4:3 standardTV
Select "4:3" (l)age 45).
l_! Select "Finish
Setup,"
and press ENTER.
"_° Hints
• If you want to reset these settings to their lactory dehmlts, see
"Resetting the Player" (page 53).
• You can reran Easy Setup from "Options'
Setup (page 52).
The following
settings
and adjustments
are necessary
when your
connection
applies.
For video connection
*When using theCOMIPONENT
VIDEO OUT jacks
(Pattern
(_ -page
11)
• Select
the video output resolution
for your TV by pressing
VIDEO
FORMAT
if)age 46).
*When using theHDIVll OUT jack
(Pattern
(_) _)age
12)
• Select
the video output resolution
for your TV by pressing
VIDEO
FORMAT
(page 45).
• Select
the type of vkteo output
from the HDMI jack in "YCb
Cr/RGB
PC (HDMI)"
of"Video
Setup"
(page 45).
For audioconnection
*When
using the DIGITAL OUT (OPTICAL or COAXIAL) jack
(Connection _),
_,
_
pagr, 14 to l(,)
• Set "Dolby
Digital"
and "DTS"
in "Audio
Setup"
(page 47)
according
to your AV amplifier's
(receiver's)
decoder.
*When
using the HDIVll OUT jack
(HDMI
connection
of _,
_
-pag,,
16)
• Set "Dolby
Digital"
and "DTS"
in "Audio
Setup"
(page 47)
according
to your AV anaplifier's
(receiver's)
decoder.
• Select the audio output method from the HDMI jack in "Audio
(HDM])"
of"Audio
Setup."
*When
using the AUDIO OUT (L/R) jacks
(Connection
4[_
-l)agr ' 1.5)
• Set "DTS Downmix"
to "Lt/Rt"
in "Audio
Setup"
(page 47).
*When using the5.1CHOUTPUT j acks
(Connection
_
_)age
1.5)
• Set "Audio
Output
Mode"
to "5.1 Channel"
in "Speakers"
Setup (page 51), and adjust the "Speaker
Setup" setting
for
your system.
• If you connect a component that does not conform to the selected audio
signah a loud noise (or no sound) will come out fi'om the speakers,
which could damage your ears or speakers.
• If you connect using the HDMI OUT jack or COMPONENT
VIDEO
OUT jacks and the picture does not appear clearly, the connected
display device may not be compatible with the progressive signals. In
this case, connect the display device to the S VIDEO jack or the
VIIDEO jack (pattern (_) or (_)
see page ll), re-run the "Easy Setup"
from the "Options" Setup (page 52), and select "S-Video/Video
Only"
in step 6 (page 19). Also, check the above items again to see if any
additional atliustmeut is required.
0
Step 7: Additional Adjustments
BDP-S1 (US)
2-687-794-11 (1)
Advertisement
Table of Contents
