Download Print this page

Epson P07303 User Manual

Epson stand alone vfd pole display user's manual
Hide thumbs

Advertisement

Quick Links

USER'S MANUAL
P07303 Stand Alone VFD Pole Display
48200550
(January,2002 V1.0)

Advertisement

loading

  Related Manuals for Epson P07303

  Summary of Contents for Epson P07303

  • Page 1 USER’S MANUAL P07303 Stand Alone VFD Pole Display 48200550 (January,2002 V1.0)
  • Page 2 General Notice: All the company names used herein are for identification purposes only and may be trademarks of their respective companies. NOTICE The contents of this manual are subject to change without notice. P07303 Stand Alone VFD Customer Display Copyright of Manufacture December 2001 (Reversion 1.0) Part No. 48200550...
  • Page 3: Table Of Contents

    7.5 AEDEX mode command list... 19 7.6 ADM787/788 mode command list ... 20 7.7 DSP-800 mode command list ... 20 7.8 EPSON ESC/POS command list-1 ... 21 8. Character Set ... 23 8.1 International Character Sets ... 23 8.2 USA, Standard Character Sets (20H – 7EH) ... 23 8.3 Page 0 (PC437: USA, Standard Europe) (80H –...
  • Page 4 8.7 Page 4 (PC863: Canadian-French) (80H – FFH) ... 25 8.8 Page 5 (PC865: Nordic) (80H – FFH)... 26 8.9 Page 6 (Slavonic) (80H – FFH)... 26 8.10 Page 7 (Russia) (80H – FFH) ... 27 9.Command details... 28 9.1 Overwrite mode... 28 9.2 Vertical scroll mode ...
  • Page 5: Features

    (2) Blue–green color and large character are easy to see (3)The DIP switches setting emulate commands mode, baud rate and international character. (4) Command emulation modes include POS7300/ CD5220 II/ ADM787/ UTC / AEDEX/ Epson/ DSP800. (5) User’s-defined character and message can be downloaded.
  • Page 6: General Specification

    2. General Specification ITEM Descriptions Display method Vacuum fluorescent display 40 characters Number of character ( 20 columns x 2 lines) Character font 5 x 7 Dot matrix Display color Blue green Brightness 700 cd / 96 alphanumeric Character type 13 kinds of international character set 1 kind of user define character Character size...
  • Page 7: Unpacking And Checking The Parts

    3 Unpacking and Checking the Parts 225 mm 93 mm •Pole Display Module •Flat Cable (DB-9P to DB-9P flat cable connector ) •Base Unit •Two pieces of pole support (1x22cm, 1x9cm) •Installation guide •Power Adapter...
  • Page 8: Interface

    4. Interface 4.1 Specifications Data transmission: Serial Synchronization: Asynchronous Handshaking: DTR / DSR MARK = -3 to –15 V (logic “1”) Signal level: SPACE = +3 to +15 V (logic “0”) Baud rates: 4800,9600,19200,38400 bps Parity: None, even Bit length: 8 bits Stop bits: 1 or more...
  • Page 9: Interface

    4.3. Interface 4.3.1 Stand alone VFD Pole Display Below illustrate the configuration of Stand alone VFD Pole Display base. Figure of VFD Pole Display Base ●Interface connector on the bottom of Pole Display Base (standard ) ●Interface connector on the bottom of Pole Display Base (option ) CN2 CN1 CN2:Power input connector from adapter ( range from 9-35VDC, Manufacture offer +12V power adapter )
  • Page 10 CN2: RS-232C connects to PC/Host CN3: Connect to display panel CN6: Power supply connector CN1,CN4, CN5: No used Power Supply Connectors CN6 / Connector type: DC jack (5.5/2.1) Pin assignment Signal RS232C link to PC/HOST connector CN2 / Connector type: D-sub 9 pin female Pin assignment Signal Direction...
  • Page 11: Dip Switch And Software Setting

    5. Dip Switch and Software Setting 5.1 Command type selection 5.2 Baud rate selection Baud rate (bps) 4800 9600 19200 38400 5.3 Parity check selection SW10 Parity check None-parity Even-parity 5.4 Demo Mode selection SW11 Show demo string Enable Disable Command type Default POS7300...
  • Page 12: International Character Set

    5.5 International character set SW4 SW5 SW6 SW7 Character set *default U.S.A. FRANCE GERMANY U.K. DENMARK I SWEDEN ITALY SPAIN JAPAN NORWAY DENMARK II SLAVONIC RUSSIA U.S.A Not used Used define pattern from EEPROM 5.6 Self-test SW11 function Power on self-test No test * SW12 is reserve Code table ( 80H-FFH)
  • Page 13: Software Status Setting

    5.7. Software Status Setting When system POWER ON, there is no need to turn off to modify Command Type, Baud Rate, Parity, Demo Mode and International Character. To re-set DIP Switch to various Command Type under the following list of Command to modify the setting. The setup value will stored in the EEPROM. When DIP Switch is OFF.
  • Page 14: Command Type Select

    nternational font .S.A. RANCE 32h GERMANY 34h DENMARK I WEDEN 36h TALY PAIN 5.7.3 Command type select /Change command type/ STX 05 C n ETX ASCII Format STX 05 C n ETX Dec. Format [02][05][67] n [03] Hex. Format [02h][05h][43h] n [03h] Description This command will change the command type and initialize the display.
  • Page 15: Reset Eeprom

    5.7.4 Reset EEPROM /Reset EEPROM/ STX 05 07 n ETX ASCII Format STX 05 07 n ETX Dec. Format [02][05][07][n][03] Hex. Format [02h][05h][07h][n][03h] Description This command will reset the content of EEPROM (e.g. Demo scroll data, user-define character) Description Clear all EEPROM contents Clear upper line data message Clear lower line data message 5.7.5 Save data for demo display...
  • Page 16: Set Communication Parity

    5.7.7 Set Communication parity /Parity check selection/ STX 05 P n ETX ASCII Format STX 05 P n ETX Dec. Format [02][05][80] n [03] Hex. Format [02h][05h][50h] n [03h] Description Change the display communication parity. Set 8 data bit and the parity set for even or non-parity.
  • Page 17: Command List Table

    6. Command List Table Table –1 FLYTECH PARTNER EPSON POS7300 CD5220 Move cursor right Move cursor left Move cursor up Move cursor down Move cursor to right-most position Move cursor to left-most position Move cursor to home position O Move cursor to bottom...
  • Page 18 Table-2 FLYTECH PARTNER EPSON POS7300 CD5220 Upper line message scroll once pass Change attention code Two line display Clear upper line and move cursor to upper left-end position Clear bottom line and move cursor to bottom left-end position Set period to upper line, last n...
  • Page 19: Command

    7. Command 7.1. POS7300 series command set POS7300 Standard Mode Command List Command Code (hex) ESC F A .. CR 1B 46 41 [DATA X 40] 0D ESC F B .. CR 1B 46 42 [DATA X 40] 0D ESC F D .. CR 1B 46 44 [DATA X 40] 0D ESC F O ..
  • Page 20: Cd5220 Standard Mode Command List

    7.2 CD5220 Standard Mode Command List Command Code (hex) ESC DC1 1B 11 US SOH 1F 01 ESC DC2 1B 12 US STX 1F 02 ESC DC3 1B 13 US ETX 1F 03 ESC Q A .. CR 1B 51 41 [n]x20 0D ESC Q B ..
  • Page 21 CD5220 Standard Mode Command List-2 Command Code (hex) ESC I x y 1B 6C x y / 1F 24 x y 1 x 20, y=1,2 US $ x y 1F 24 x y 1 x 20,y=1,2 ESC @ 1B 40 ESC W s x1 x2 y 1B 57 1 x1 x2 y 1 x1 x2 20 y=1,2...
  • Page 22: Utc Standard Mode Command List

    *2: The parameter of international fonts set control by command “ESC f n” Parameter n ‘A’ ‘G’ ’I’ ‘J’ ‘U’ ‘F’ ‘S’ ‘N’ ‘W’ ‘D’ ‘E’ ‘L’ ‘R’ *3: The parameter of the code table control by command “ESC c n” Parameter “n”...
  • Page 23: Utc Enhanced Mode Command List

    7.4 UTC enhanced mode command list Command Code (hex) ESC u A .. CR 1B 75 41 [data x 40] ESC u B .. CR 1B 75 42 [data x 40] ESC u D .. CR 1B 75 44 [data x 40] ESC u E ..
  • Page 24: Adm787/788 Mode Command List

    7.6 ADM787/788 mode command list Command Code (hex) SLE1 SLE2 10 n 11 n 7.7 DSP-800 mode command list Command Code (hex) EOT SOH I n ETB 04 01 49 n 17 n=00~0Fh or 30~3Fh EOT SOH P n ETB 04 01 50 n 17 n=31h-58h EOT SOH C n m...
  • Page 25: Epson Esc/Pos Command List-1

    7.8 EPSON ESC/POS command list-1 Command Code (hex) US LF 1F 0A US CR 1F 0D US B 1F 42 US $ x y 1F 24 x y (x=1~20, y=01,02) US X n 1F 58 n (01 n 04) US E n...
  • Page 26 EPSON Esc/pos command list-2 Command Code (hex) ESC W n s x1 y1 x2 y2 1 B 57 n s x1 y1 x2 y2 n=1,2,3,4 s=0,1 ESC = n 1B 3D n n=1,31,select printer n=2,32,select display n=3,33, select printer, display...
  • Page 27: Character Set

    8. Character Set 8.1 International Character Sets 8.2 USA, Standard Character Sets (20H – 7EH) 23 3...
  • Page 28: Pc437: Usa, Standard Europe) (80H - Ffh)

    8.3 Page 0 (PC437: USA, Standard Europe) (80H – FFH) 8.4 Page 1 (Katakana) (80H – FFH) 8.5 Page 2 (PC850: Mulitlingual) (80H – FFH) 24 4...
  • Page 29: Pc860: Portuguese) (80H - Ffh)

    8.6 Page 3 (PC860: Portuguese) (80H – FFH) 8.7 Page 4 (PC863: Canadian-French) (80H – FFH) 25 5...
  • Page 30: Pc865: Nordic) (80H - Ffh)

    8.8 Page 5 (PC865: Nordic) (80H – FFH) 8.9 Page 6 (Slavonic) (80H – FFH) 26 6...
  • Page 31: Russia) (80H - Ffh)

    8.10 Page 7 (Russia) (80H – FFH) 27 7...
  • Page 32: Command Details

    9.Command details 9.1 Overwrite mode In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor reached the end of the upper line, the cursor will move down to the bottom left-end position to continue.
  • Page 33: Move Cursor Up

    9.8 Move cursor up Move the cursor up one line. When the or is on the upper line, this command operates differently depending on the display mode. Overwrite mode: The cursor is moved to the same column the lower line. Vertical scroll mode: The characters display on the upper line is scrolled to the lower line, and the upper line is cleared.
  • Page 34: Clear Display Screen, And Clear String Mode

    9.17 Clear display screen, and clear string mode All the display characters will be cleared, and the string mode will be cancelled. 9.18 Clear current line, and cancel string mode The current line is cleared, and the string mode is cancelled. 9.19 Brightness adjustment Adjust the brightness of the vacuum fluorescent display.
  • Page 35: Character Font Format

    9.26 Character font format One font consists of 5 bytes’ string. The string format is: yte 1 R7C1 yte 2 R7C2 yte 3 R7C3 yte 4 R7C4 yte 5 R7C5 10. Control code set CODE NULL SOH, MD1 STX, MD2 ETX, MD3 EOT, MD4 ENQ, MD5...
  • Page 36: Appendix A: Display Module Dimension

    Appendix A: Display Module Dimension 200mm 176mm 158.6mm 5.25mm 0.85mm 0.25mm 1.05mm 0.25mm 9.0mm 1.5mm 1.5mm 1.5mm 6.65mm 0.38o 70mm 39mm 9.5mm 22.5mm 32 2...