Advertisement
Available languages
Available languages
Read and understand
all instructions.
Failure to follow all instructions
listed below, may result in electric
shock, fire and/or serious personal
injury.
SAVE THESE
INSTRUCTIONS
Work
Area
Keep your work area clean and well lit.
Cluttered
benches
and dark areas invite
accidents.
Do not operate
power tools in explosive
atmospheres,
such as in the presence
of
flammable
liquids,
gases,
or dust.
Power
tools create sparks which may ignite the
dust or fumes.
Keep by-standers,
children,
and visitors
away while operating
a power tool.
Distractions
can cause you to lose control.
Electrical
Safety
Double Insulated
tools are equipped
with
a polarized
plug (one blade is wider
than
the other.)
This plug will fit in a polarized
outlet
only one way.
If the plug does not
fit fully in the outlet,
reverse the plug.
If it
still does not fit, contact
a qualified
electrician
to install a polarized
outlet.
Do
not change
the plug in any way. Double
Insulation []
eliminates
the need for the
three wire grounded
power cord and
grounded
power supply system.
Before
plugging
in the tool, be certain the outlet
voltage supplied
is within the voltage
marked
on the nameplate.
Do not use "AC
only" rated tools with a DC power supply.
Avoid body contact
with grounded
surfaces
such as pipes, radiators,
ranges
and refrigerators.
There is an increased
risk of electric
shock if your body is
grounded.
If operating
the power tool in
damp locations
is unavoidable,
a Ground
Fault Circuit
Interrupter
must be used to
supply the power to your tool. Electrician's
rubber gloves and footwear
will further
enhance
your persona] safety.
Don't expose power
tools
to rain or wet
conditions.
Water entering
a power tool
will increase the risk of electric
shock.
Do not abuse the cord. Never use the
cord
to carry
the tools
or pull the plug
from an outlet. Keep cord away from
heat, oil, sharp edges or moving parts.
Replace
damaged
cords immediately.
Damaged
cords increase the risk of electric
shock.
When
operating
a power
tool outside,
use an outdoor extension
cord
marked
"W-A"
or "W." These cords are rated for
outaoor
use and reduce the risk of electric
shock.
Refer to "Recommended
sizes of
Extension
Cords" in the Accessory
section
of this manual.
Personal
Safety
Stay alert, watch
what you are doing
and
use common
sense when operating
a
power tool. Do not use tool while
tired
or
under
the influence
of drugs,
alcohol,
or
medication.
A moment
of inattention
while
operating
power tools may result in serious
personal
injury.
Dress properly.
Do not wear
loose
clothing
or jewelry.
Contain
long hair.
Keep your hair, clothing,
and gloves
away from
moving
parts.
Loose clothes,
jewelry,
or long hair can be caught in
moving
parts. Keep handles dry, clean and
free from oil and grease.
Avoid
accidental
starting.
Be sure switch
is "OFF"
before
plugging
in. Carrying
tools with your finger on the switch or
plugging
in tools that have the switch "ON"
invites accidents.
Remove
adjusting
keys or wrenches
before turning the tool "ON".
A wrench or
a key that is left attached
to a rotating
part
of the tool may result in personal
injury.
Do not overreach.
Keep proper footing
and balance
at all times.
Proper footing
and balance enables better control
of the
tool in unexpected
situations.
Use safety equipment.
Always wear eye
protection.
Dust mask, non-skid
safety
shoes, hard hat, or hearing protection
must
be used for appropriate
conditions.
Tool
Use
and
Care
Use clamps
or other
practical
way to
secure
and support
the workpiece
to a
stable
platform.
Holding the work by hand
or against your body is unstable
and may
1end to toss of control.
Do not force tool. Use the correct
tool for
your application.
The correct
tool will do
the job better and safer at the rate for which
it is designed.
Do not use tool if switch
does not turn it
"ON" or "OFF". Any tool that cannot be
Advertisement
