Craftsman 137.215360 Owner's Manual

4"x36" belt 6" disc belt/disc sander
Hide thumbs


4" × 36" Be_t
6" Disc
_lod÷_ No,
Before using this Belt / Disc Sander,
read this manuai and follow
all its Safety Rubs and
o Safety Instructions
o _nstallation
o Operation
o Maintenance
o Parts List
o Espa_oi
1 °81@°848=1882
and Co_ Hoffman
_L (}0!79
Part No, 1372t5360001



  Related Manuals for Craftsman 137.215360

  Summary of Contents for Craftsman 137.215360

  • Page 1 4" × 36" Be_t 6" Disc _lod÷_ No, !37o2t5360 o Safety Instructions CAUT_©N: o _nstallation Before using this Belt / Disc Sander, o Operation read this manuai and follow o Maintenance all its Safety Rubs and o Parts List Operating _nstructions, o Espa_oi 1 °81@°848=1882...
  • Page 2: Specifications

    SECTION PAGE GENERAL SAFETY INSTRUCTIONS w_A_ Your ALWAYS WEAR EYE PROTECTION. Any belt / disc Warranty ..............BEFORE USING THE BELT/DISC SANDER sander can throw foreign Product Specifications ............objects into the eyes which Safety Rnstructions ............Safety is a combination of common sense, staying alert could cause permanent eye and knowing how to use your belt / disc sander.
  • Page 3 GROUNDING DNSTRUCTIONS 24. DONOToperate t hetoo!ifyouareunder t heinfluence 12.ALWAYS maintain a minirnum clearance o f 1/16inch This tool is intended for use on a circuit that has a ofanydrugs, a lcohol o1" m edication t hatcould affect or lessbetween thetableorbackstop a ndthesanding receptacle like the one illustrated in FIGURE A.
  • Page 4: Bench Belt/Disc Sander Overview

    DESCRiPTiON _QUANTITY Belt / Disc Sander Disc Disc housing AVAHLABLE ACCES._ ,OR ES Disc table k/liter gauge Sanding disc Disc housing Back stop Tension lever Sanding belt Disc dust chute Belt dust chute Use only accessories recommended for this belt / disc Loose parts in bag: sander.
  • Page 5: Assembly

    ASSEMBLY INSTRUCTIONS PULLEY COVER INSTALLATION (FIG. E) SANDING DiSC iNSTALLATION (FIG. G) Attach pulley cover (1) using the 40mm long pan head Remove and clean any adhesive or material left on the screw (2) and 12mm pan head screw (3), as shown. disc plate (2).
  • Page 6: Table/Dust Chute Installation

    TABLE ASSEMBLY INSTALLATION (FIG. I) ADJUSTMENTS Fig. J The worktable can be used with either the sanding disc or the sanding belt. It should be used to support workpieces in all sanding operations except inside curve applications. Insert the table support rod (1) into the sander base To avoid injury, always keep the plug disconnected from the power source and the switch turned OFF until the hole as shown.
  • Page 7: Replacing Sanding Belt

    SAFETY POWER SWITCH (FIG. O) WRENCH (F1G. Q) REPLACmNG SANDING BELT (FIG. S, T, U) Fig. U Insert the handle of the wrench into the metal clip located on the sander as shown. To avoid injury, always keep the plug disconnected from To avoid injury, turn switch OFF and disconnect the plug Fig, Q the power source and switch turned OFF until the sander...
  • Page 8: Adjusting Sanding Arm

    ADJUSTING SANDING ARM SANDING INSIDE CURVES (FIG. Y} END GRAIN SANDING WITH THE BELT (FroG.AA) Freehand sanding of inside curves can be sanded on the When sanding the ends of the wide workpieces it is LEVELING THEARM(FIG. W ) idler drum (1). Never attempt to sand the ends of a more convenient to use the sanding belt (1) with the A positive stopis provided t o position thesanding arm workpiece on the drive drum.
  • Page 9: Troubleshooting

    TROUBLESHOOTUNG GUIDE For your own safety, turn switch OFF and remove plug To avoid shock or fire hazard, if the power cord is worn or from the power source outlet before maintaining, or cut or damaged in any way, have it replaced immediately. lubricating your belt / disc sander.
  • Page 10: Parts List

    SANDER MODEL Nee 137.215360 When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this belt / disc sander may create a HAZARD unless repair is done by a qualified service technician, Repair service is available at your nearest Sears Service Center.